2. cables
  3. 1408823487

Wierd issue with a DIY cable for a REL G2 sub

I built a cable for my uncle for his REL G2. He wanted a cable shorter than the 35' one that came with the REL. It is causing a thermal issue with the McCormack amp that is being used for the high level source. He says it plays fine for about 5 minutes, then thermals and shuts off. The OE REL cable does not have the problem (obviously). Here is the breakdown of the cable:

Neutrik NLT4FX speakon connector (I used this so I could have a solder connection instead of compression, also the aluminum casing is just nicer)

15' Belden 5102UP 14ga speaker cable (using 3 of the 4 conductors)

14ga spade terminals

Connections at the speakon end are soldered with WBT silver bearing solder and connected to the same lugs in the speakon as the original cable.

At the spade end, the connections are crimped, then soldered with WBT silver solder as well.

All 3 wires for the cable show continuity to the appropriate point on the speakon, and show no continuity to each other.

All 3 connections read .3 ohms of impedance between the spade and the speakon. As well as .3 ohms when testing between the input and output of the speakon.

I'm stumped. The OE cable didn't look like it had any kind of special circuit attached with it so I assumed it is just copper wire.

At this point I am thinking voodoo devil magic.

Anyone have any thoughts or input?
diamondjoequimby
mitch2
4,202 posts
 
Ok, so I found this;
REL manages the lower frequencies differently than other manufacturers—and does so with excellent result. While the company offers line-level RCA inputs, these should be used only as a last resort. The supplied Neutrik speakON connector utilizes a high-level connection that goes directly to your power amplifier’s speaker outputs. The sub’s high impedance does not affect loading of the main speakers, thus allowing the character of your amplifier’s sound to carry forward into the subwoofer.
My first thought was to recommend trying the line level outputs from the preamp but it appears that using the high level speaker cables to connect the sub to the speaker cable output terminals of the McCormack amp is the preferred approach, since that is designed to result in superior blending with the sound of the amplifier that is being used to power the upper frequencies.

Hopefully, this is a grounding issue, as Al suspects, and one of his recommendations will solve the problem.

I do have a couple of additional thoughts. First, I noticed you used only three of the four wires in the Belden speaker cable, which would result in an unbalanced configuration with one polarity having a larger gauge wire than the other (whichever side has two wires vs. one). Since most speaker cables use the same gauge wires for the positive and negative poles, you could try connecting the cable in a star-quad configuration where the two wires opposite each other are connected together to form each polarity. Based on the pictures I found, it appears you would connect the black/white wires together and red/green wires together.

Also, you might check the polarity of your wire connections in both channels to make sure they are consistent.
almarg's avatar
almarg
9,670 posts
 
Tim (Mitch2), thanks for the additional thoughts. Be aware, though, that the three wires which connect to the speaker-level inputs of a REL sub are not used as you appear to be envisioning. One wire carries the + signal of one channel; another wire carries the + signal of the other channel; and the third wire provides a return (-) path for both of the channels. (When monoblock amps are being used in conjunction with a single sub, REL recommends connecting that single return wire to a ground point on the preamp, rather than on one of the amps).

Also, as with most powered subs having speaker level inputs the impedance of those inputs is extremely high, 100K for many of the REL models, so essentially negligible amounts of current are being conducted. As you'll realize, a single 14 gauge conductor is overkill by a wide margin. And of course effects that the cable might have on mid and high frequencies won't matter.

Best regards,
-- Al
mitch2
4,202 posts
 
I see that now Al, thanks. I should have researched it more closely. I use line level connectors for my Alon and Aerial subs and have not used a REL sub. I see the referenced Neutrik speakON connector is a four pole connector. I hope he gets it sorted out since it seems he was doing his uncle a favor.
diamondjoequimby OP
9 posts
 
Al is right, the 14ga is way overkill and the 4th conductor in the Belden cable is simply not needed. Nor is the 4th pole on the SpeakOn. However it is tough to fine decent 3 conductor cable (or 4 for that matter) by the foot. And seeing as I didn't need a 500' spool, I went with the readily available 14ga Belden 5000 series 4 conductor.

And yes, this is a favor for a family member. When I saw that he was looking at spending between $150-$600 for a sub cable using what I knew to be a $4 SpeakOn, I offered to make one for him for a fraction of the cost.

I made all the cables (interconnect, XLR, and speaker) for my own system and never ran into issues before, so after looking at the stock REL one, this seemed like a piece of cake!

If it is a balanced output amp and the REL uses the black as a return to the amp, Al's insight seems like the likely culprit. I'm waiting to hear back from my uncle, but hopefully this will do the trick.

I'll report back with what I find out.
joseph54
7 posts
 
Please forgive my intrusion to this discussion with an unrelated REL subwoofer issue but the thermal shut down issue caught my attention. My REL Strata II sub has recently developed a hum and I do not know why. My NAD C375BEE has recently been shutting down via the protection circuit even with the REL powered off. Might the hum issue with the REL be able to cause this problem with my amplifier? Thank you, Joseph
More to discover