2. amps-preamps
  3. 140826-115924

Cabinet clearance for Audio Acoustics LS16 tube pre-amp?

I am in the process of designing a built in cabinet for my stereo system. The owner's manual for the Proceed HPA2 amp is very clear about clearances for air flow. And even in the summer it almost never feels very hot as it has enormous aluminum heat sinks with completely open airflow from top to bottom.

The owner's manual for the LS-16 does not give any specifics. It says things like "adequate airflow" and that with a closed back cabinet, which mine will be, an exhaust fan is "desirable". That's about all they say. And it runs noticeably hotter than the amp. The top is never too hot to touch by any means but it is warm to the touch. Currently it sits on top of basic component stand and is up on some raised blocks so it gets all the airflow it could possibly need.

I could put it on top of the built-in shelves but I'd prefer not to. I'd also prefer not to have an exhaust fan humming along all the time. But, I don't want to shorten tube life or hurt the unit either.

Any recommendations? Precautions? Prior experience with your set-ups with tube pre-amps? 

Thanks,

George
n80
djones51
4,947 posts
 
One way to get an idea of how hot it gets is make a box out of scrap wood about the size of the opening you want the preamp to fit in, set it over the preamp and run it for a few hours and see how hot it gets. That's the way I was thinking about the fan. Use a  small flush mount in the back blowing the air  outwards , get one with a thermostat I doubt it would run that often. 
Ag insider logo xs@2x
cleeds
5,944 posts
 
n80
I checked out the link to the fans cleeds provided. Interesting. They do make a front exhaust model which would be the only one that would work for me ...
Same here, except I use the rear-exhaust version.
Sound level is reported as 24 dB.
My listening chair is about 14 feet from the AC Infinity unit and I never hear it.
While I’m not a major audio tweaker I do wonder what folks with power conditioners and Noise Harvesters in all their outlets would say about putting an electric motor physically on top of their pre-amp? Maybe no issues at all.
I have no issues with noise from the AC Infinity unit. I do plug it into a separate outlet, along with things like the Littllite that I use over the turntable. All my other equipment goes into a power conditioner.

I’m not sure why you consider the information I’ve offered here “petulant” but I’m providing it anyway for the possible benefit to others.

n80 OP
2,116 posts
 
@cleeds Thank you for the info. I do appreciate it.

"I’m not sure why you consider the information I’ve offered here “petulant” "
Maybe this just rubbed me the wrong way:

"It’s just that you don’t like the advice offered."

I did not think that it was the correct assessment or a necessary one. Again, maybe its just me.
n80 OP
2,116 posts
 
Thinking about this more....probably too much...a couple of things occurred to me.

First, I suspect that the owner's manual for the LS16 is talking about a completely enclosed rack or cabinet when it talks about a fan being desirable if the back is closed. That seems to imply a rack/cabinet enclosed on all four sides. Maybe not. It isn't clear.

Second, looking through pictures of user's systems here at Audiogon there are a fair many that have components, including tubed, in closed back shelves. There are tons that have components in open audio racks but that are right up against a wall which is pretty much the same as a closed back and that have other components right next to them on either side.

However, my current plan, #103 (b), is to put the pre-amp on top out in the open. I've also decided to skip the false wall for cables to go behind. While it might look better it will making moving or adding components a nightmare. It would also give less rear clearance which would decrease airflow around the components.
More to discover