2. home-theater
  3. 1261302622

Need Processor Input

Okay, I need some input. I have a Theta Casablanca I with standard dacs that has served me well. I run a Naim CDX CD player through the analog direct so reason the standard dacs have been good enough on movies for me. Unfortunately when I purchased my CBI, I didn't get the DTS board. Now with Blu-ray having so many titles with DTS, I'm wondering what to do. I could buy a used processor that does both dolby digital and DTS in lossy and save a lot of money and still have a good preamp for my CD player or buy an Integra for $2k which probably would force me to run a separate preamp proably for another $2k or slightly less if used.

I'm not wanting to get in a debate over lossless vs lossy but I read an article off the internet where a group of reviewers went to Dolby Digital Labs and DTS to hear sections of movies both in lossless and lossy in a controlled environment with expensive gear. Most could NOT hear any difference while a couple did but said it was very slight with lossless being a touch better. The improvement was described as being slightly fuller sound with slightly more surround information.

With this, I'm wondering if I should really get the Integra 9.9 that could do all the lossless but also have to buy a preamp or just buy a used processor for a fraction of the cost and still be pretty darn happy. I can tell with my CBI that the sound of blu-rays sound better than the same standard dvd copy but that could be due to a different sound mix. I just watched the Blu-ray movie of Nightmare Before Christmas in plain DD 5.1 and couldn't believe the improved surround sound and clarity of the songs in the movie. It sounded so good that I really wondered how much lossless or better dacs could really improve the overall sound. This was the big reason in the beginning for not spending so much on Theta's expensive upper end dacs and deciding the standard dacs would be pretty darn good for movies. As for movies and music, a couple of the biggest factors is the source recording and the listening environment besides the rest being the equipment.

Any thoughts from those that have gone from an older processor to something newer???
robertrobert
Ag insider logo xs@2x
dbphd
1,628 posts
 
Zephyr,

Can you recommend some preamps with HT bypass?

db
zephyr24069's avatar
Ag insider logo xs@2x
zephyr24069
1,243 posts
 
Oops....my last post (12-21) once it is approved has discussion on balanced bypass. You were asking about HT bypass for which there is ample support from Classe procs and MANY others on the market.
joelz
25 posts
 
I'm confused on what your asking and what a CBI is. However, I do have an old processor and a new bluray player (Pioneer Elite BDP-09FD). I use analog out from the 09FD into my classe ssp-600.

Then the classe goes to my McIntosh C500t pre-amp in home theater bypass mode.

It sounds fantastic!

I just got through doing homework on whether or not I will get better Blue-Ray sound by getting a processor that can handle the codecs. The answer is I have the best for my price point. I would have to spend around 7k+ for a processor to get better HT sound.

I hope that helps!
robertrobert OP
1 posts
 
Hello Joelz,

The CBI stands for the Theta Casablanca I. It is so outdated that it doesn't have the analog inputs needed like you're using. I'm only using a coax digital cable for dolby digital. Maybe I should buy a used processor that has this since I have a Toshiba XA2 HD DVD player that has the 7 analog outputs and a Panasonic BD80 Blu-ray player that has them as well. I wasn't sure if the decoding sound in a new processor would actually sound better or not so your input is appreciated. Who told you that you would need to spend $7k to get better sound? I believe it since I've heard the conversion in the XA2 and BD80 is quite good. I've heard the tricky part is setting up the surround when using the analog outputs from the source player usually with the subwoofer sometimes having lower output for some reason.

I don't feel that I have to spend the money on a new processor with all the latest codecs to try and get close to the best sound possible for home theater. The reason I'm even considering upgrading is that I never had a DTS board installed in my Casablanca. Now that Blu-ray has won with so many titles using DTS only, the sound quality isn't as good with my Casablanca simulating 5.0 via a mode called special matrix where it take 2 channels of DTS and send them to my processor while the BD80 down mixes the other 3.0 channels to simulate the 5.0. It doesn't sound bad but not nearly as good as even simple 5.0 dolby digital.
joelz
25 posts
 
Robert, my local audio store and a few folks on the internet (avsforum) are the ones I took advice from and think the BDP-09FD (analog out) + Classe SSP600 has very good sound as the 09FD is an audiophile grade player and the Classe is still fantastic sounding even though its the older generation classe.

The next gen (or current generation) Classe, the SSP800 is ~$8k, the top end Marantz and Denon HT procs (seperates) are $7k and there isn't many offering inbetween that I've looked at which would give better sound and cost less than 7k-8k.

I asked about the Integra (Onkyo) 9.9 and 9.8 used in conjunction with the 09FD via HDMI and the sound quality with that configuration and it still would not be an upgrade.

They didn't mention what grade of analog audio the BD80 had (I didn't ask about that one).

Thats right, there is no real need to get a proc with the latest codecs if you have a Blue-Ray player with good analog outs.

The Classe SSP600/SSP300 processor is nice, but it lacks bells and whistles (and lots of them). Perhaps thats why it sounds so good.
More to discover