2. amps-preamps
  3. 147677-2029

Question About Audio Research Preamp Specs

Hi,

I am trying to understand Audio Research terminology while looking at their product specs.

For example, for the LS28 OUTPUT IMPEDANCE, it reads "600 ohms Balanced, 300 ohms SE Main (2), 20K ohms minimum load and 2000pF maximum capacitance..."

What does the  "20K ohms minimum load" tell me?

I am running a McCormack DNA-500 and it has an input impedance of 10K Ohms. It would seem that the amp would be compatible with this preamp based on the 10X/15X minimum rule of thumb. 

My concern is that the AR spec is telling me use amps with input impedance of 20K ohms and the DNA would not work well.

Thanks for listening,

Dsper
dsper
audioconnection
1,271 posts
 
George
 Makes great sense here.
  easy to have a tech make the resistor changes on the power amp
 .sometimes I wonder if guys like Rowland and McCormick make amps input Imp so low that only their own preamps have an advantage even over great pre amps.
georgehifi's avatar
georgehifi
10,312 posts
 
audioconnection
 George
Makes great sense here.
easy to have a tech make the resistor changes on the power amp
.sometimes I wonder if guys like Rowland and McCormick make amps input Imp so low that only their own preamps have an advantage even over great pre amps.

That’s more truth than fiction, we have a very good power amp maker here that has 1kohm input, and yes his preamp is 10ohms, so any other preamp sounds like **** into it but his doesn’t.
But the 1k input resistor on the amp is socketed and if removed the input becomes 68kohms, but he doesn’t advertise this, and any preamp/tube ss/or passive will drive it then.

Cheers George
atmasphere's avatar
atmasphere
11,945 posts
 
1: If you own the AR pre, tell me the size (uF) of the output coupling cap, (it will be the big ones near each output) and what the poweramp input impedance is you want to use it with, and i’ll calculate at what low frequency it’s at -3db for you.
It’s a simple to correct if too small, with a $20 larger coupling cap, don’t go buying another preamp because of it.

2: Or you can go the other way and get the input impedance resistor (20cents) raised to 50kohm on the poweramp, if it’s fet input no problem, even a 100kohm

Cheers George audioconnectionGeorge
 Makes great sense here.
  easy to have a tech make the resistor changes on the power amp.
The reason ARC didn't do this initially was simply because the larger you make a coupling cap the more coloration no matter what type of construction. Larger caps start to get considerably higher inductance so even if you have the best Teflon its still going to be an audible degradation.
A secondary reason might also have to do with space. Adding long leads to make a part fit in a place that wasn't designed for it is a good recipe for noise pickup.

georgehifi's avatar
georgehifi
10,312 posts
 
The reason ARC didn't do this initially was simply because the larger you make a coupling cap the more coloration no matter what type of construction.
Take that with a grain of salt. I do prefer direct coupling (no cap), best cap is no cap mentality. 

But dsper OP one of the best tube preamps hailed even by many tube and solid state preamp manufactures as being the best tube preamp ever made is the  Aesthetix Calypso preamp, and it has massive output coupling caps, as shown in this pic circled in red.
https://ibb.co/4Jb0bSV

Cheers George

    
dsper OP
663 posts
 
Well now.

I like the sound of the CJ pre except for the slight LF rolloff due to the impedance issue.

Maybe I should call CJ and ask them if they can adjust the caps on the 17LS2. 

Or look into the ET5 which has a lower out impedance. 

Thanks for listening,

Dsper
More to discover