Bima, my dp80 platter could well be just like yours. I haven’t closely examined it in years. So my own description may have been inaccurate. My mat is definitely OEM, has “DENON” inscribed in the rubber on the underside, like yours. It’s thick with concentric raised ridges on the top side.
Plinth ideas for DENON PD-80 DD turntable
While my pair of Victor TT-101 still sleeping in the storage, i decided to buy another Flying Saucer.
The DENON DP-80, vintageknob always have nice images and info about rare stuff...
On that page you see DP-80 with DA-401 tonearm for hich compliance cartridges (i have this tonesm NOS). It could be an interesting project, it was hard to resist ...
The question is the Plinth for this Denon DP-80.
The original DK-300 plinth is an option, but searching for something better i found this one.
Custom made plinth is always an option and i have superb Audio-Technica AT-616 pneumatic insulators to use under the plinth.
But what do you guys using with your Denon PD-80 ?
P.S. some companies now producing even an iron cast plinth and graphite plinth, i have no access to graphite, but iron cast here is cheap to make a custom plinth.
The DENON DP-80, vintageknob always have nice images and info about rare stuff...
On that page you see DP-80 with DA-401 tonearm for hich compliance cartridges (i have this tonesm NOS). It could be an interesting project, it was hard to resist ...
The question is the Plinth for this Denon DP-80.
The original DK-300 plinth is an option, but searching for something better i found this one.
Custom made plinth is always an option and i have superb Audio-Technica AT-616 pneumatic insulators to use under the plinth.
But what do you guys using with your Denon PD-80 ?
P.S. some companies now producing even an iron cast plinth and graphite plinth, i have no access to graphite, but iron cast here is cheap to make a custom plinth.
- ...
- 75 posts total
Mine says "Denon" on the back, molded in the rubber. Yours is markedly different. I have one that closely resembles yours; more concentric rings, and lighter in weight — but of course that doesn’t mean it is like yours. "SFTG170M01" appears on the back of it; does yours have any signifier on the back? @bima well, i have stamped RGS0008 on the rubber mat, but honestly i don’t care about it, can’t remember when i’ve been using a rubber mat last time, normally i replace them with my favorite SAEC SS-300 (lightweight) or heavy Micro Seiki CU-180 (or superheavy CU-500) depends on the turntable torque and platter. |
I think your confusing the mater - the metal parts of the platter is dual coupled by leaf springs - the mat - the rubber thingy 🤣 has the label relief. The two metal platters are isolated by foam pads around their circumference by foam pads - 6 or 8 of them altered by rubber pads on the lower platter in designated pockets. The foam in all original ones are gone by now - there’s a suitable replacement available at Home Depot for $3 available - cut it into 0.875 lengths put it in place you will have 8 feet left. good Listening Peter |
The foam in all original ones are gone by now - there’s a suitable replacement available at Home Depot for $3 available - cut it into 0.875 lengths put it in place you will have 8 feet left.@pbnaudio I used weather-stripping to replace mine — is that what you mean? It's the foam-with-adhesive for sealing windows, doors, etc.* I had 4 or 5 rolls already, various sizes — one of them seemed the right width and thickness (they compress a bit, so thickness matters — too much compression, they become like hard rubber and no longer isolate; too little, and they do nothing at all). But they also come in different densities, from very spongy to quite firm. Which density, width, thickness do you recommend Peter? It seems many of the DP-80s in this thread may need it, and it's a fairly easy DIY. * Ironically, I never used any of them for insulation. Only for Audio; one of the many useful 'tweaks' at your local hardware. |
- 75 posts total