Hello everyone! Thank you for those of you that have bought our groove restoration (not cleaning) system. I would like to answer some questions that have been unanswered, or need some clarification. 1) ISonic is not our machine. iSONIC is a reseller/distributor. While we use the same overseas manufacturer, it is reasonable for us to use a a well developed ultrasonic machine. This said: Both the OE manufacturer and we at my own facility in Shenzhen make changes to machine that belong to our Company, Our IP of record. Further, the record suspension assembly we have a patent for does not damage records and holds them without damage to the labels. The machines are not the same, and ours will not damage records. 2) As to our ionizing surfactant: vinyl records repel water. Sonics need to attract the plasma wave to the record. Just adding soap or a solvent in an ultrasonic's bath in a home made DIY or professional made system and keeping a record in a sonic even for hours in an ultrasonic will never remove what is in the record grooves. This as both the water in the tank and the record hold the same charge. They repel each other. We use our ionizing spray to temporarily change the charge of the record. The plasma wave from our 35 KHz transducer (with a 503 MPH wave) is attracted to the record and then brushes in the surfactant into the grooves. Repeated steps are needed as the ionizing agent is removed over time as the record spins in the distilled water. (By the way the 1.4 ounces of 70% IPA in 1.78 gallos of water is not part of the cleaning process, it is used to kill the dormant and live fungus that ends up in the ultrasonic's s tank.) The goat hair brush with a 15 micron diameter after each 2 or 5 minute cycle when brushing onto the record the ionizing agent sees a whitish material appear. This is what the sonic in its previous cycle "softened". (Just placing a record in a sonic without this repeated process sees no groove cleaning as the charge of the record in the water returns to the same as the water (with or without a cleaning agent in the basin)). We stop the back and forth process of applying our ionizing agent when the pad dried, goat hair brush, no longer brings up materials softened by the prior cycle in the machine. IS YOUR RECORD and GROOVES CLEAN, AND RESTORED? Our process as described lets you see the process. 3) Number of records that can be processed. We may process 4 records simultaneously. Processing time for all 4 records depends on the provenance of the record : 5 , 6 or 7 two minute cycles, or 4-5 five minute cycles. With our patented process one sees what is left in the grooves. And when the grooves are clean with release agent removed. 4) Operation: Over the cycles where we re-apply the ionizing agent to the record; we remove first the films left over from prior cleaning methods used that were air dried or vacuum dried. We then remove the release agent of a new pressing or one that is 70 + years old. It is here where most of the pops reside, where dust has been micro-welded by the heat created by the dyne of the needle into the release agent. Release agent released, we now see between 1.3 and 4+ dB gain in signal over floor from your cartridge. 5) Sonic Frequency: Higher the frequency, smaller the cavitating bubble, higher the speed of the plasma wave created. One would assume as a layman higher is better. Care and Caution: Vinyl is soft. Using an ionizing agent on a record inserted into a sonic that operates at 40 KHz or higher damages the record. Do not use our bipolar agent outside of our system. Added: pouring our surfactant into the basin of some ultrasonics such as Audio Deske sees the pump seize. This where their cleaning agent in the tank mixes with what was removed from the record and our diol. Adding our surfactant into any sonic's bath serves no purpose as one needs to ionize the record over repeated cycles. Our surfactant in the bath does nothing to the restoration process. 6) Other mixes: Photoflow is not to be used in any cleaning process. It was designed for repelling water in the development of film and photos (paper). To avoid water spotting. To clean a record we need to attract a cleaning agent and process to the record. Proof to the statement: Pouring soap and water or a cleaning agent on a record that is suspended horizontally sees the water "pool", "float" on the record. The water droplet size is larger that the 30 micron groove width, and is repelled, so if one reviews the above, one can see the logic we bring to the record groove restoration process. Hope the above responds to some of the points raised. As The Absolute Sound in March 2020 stated: Billed as a record restoration device (not just a record cleaner), you'll be rewarded with a more spacious soundstage and truer instrumental timbre. In April 2020: It works with time and patience.
Questions: Contact me, Charles Kirmuss, KirmussAudio .
We are all custodians of records. Our process can restore the brilliance to records new and old, even ones that were owned by your parents and grandparents. Removing the polishes from other cleaning agents may expose the many surface scratches on the record, but now with release agent removed, the needle now rides on the true mirror of the lacquer as represented by the stamper.
