Thiel Owners

sdecker

I share your sentiments upgrading from a stock CS 2.4 to the CS 2.4SE model. Dave Garretson was one of this thread's early contributors on the benefits from using Clarity Cap OEM parts. Having spent much time w/ the 2.4, 2.4SE, 2.7 and 3.7 loudspeakers, soundstage is not a problem.

Happy Listening!

2nd Note;

I would like to hear a pair of CS 2.2 and CS 2.3 models for comparison to the CS 2.4 loudspeaker.  Happy Listening!

thosb,

Finally, and there are many on this thread who have better more experienced ears than me, but from what I have heard in my journey so far, "live" comes from tube based amplification.

I always wonder about tube amps myself. The Carver tubed 350 monos keep catching my eye.......But can they handle the 2 ohm impedance?

Thanks for listening,

Dsper

upgrading from a stock CS 2.4 to the CS 2.4SE model.

sdecker doesn’t really have SE-equivalent. The advertised changes were swapping out 13 uF polypropylene + 1 uF polystyrene for 14 uf Clarity SA and 27 uF polypropylene + 1 uF polystyrene for 28 uf Clarity SA. The unadvertised changes were sourcing the boards from FST which reduced the parts quality of the other caps as well as coils (not sure about the resistors). FST were also printed circuit boards instead of point-to-point. It’s also *possible* that the hookup wire on the CS2.4SE was not as good as the original CS2.4.

sdecker kept the 1 uF polystyrenes and used Clarity ESA (instead of SA) to replace the 13 and 27 uF coax feed caps. Probably, sdecker has something *better* than the SE-version although I’m curious to know the sonic consequences of the 1 uF bypasses relative to full capacitance from single caps (ie, 14 and 28 uF). Perhaps Tom Thiel’s trials will include comparisons with and without the 1 uF bypasses.

I don't have full vs 1uF bypass comparisons, but I do have some relevant history. When Thiel developed the bypass configuration, caps were relatively primitive, and smaller value, higher spec bypass caps made a significant improvement. We developed that 1uF tin foil x styrene cap as state of the art and used it for nearly every station. Note that the CS3 had teflon nF double bypasses and the CS2 and 3.5 had styrene ultra bypasses. As caps got better, the ultra bypasses became effectively obsolete. Note that multiple caps help and hurt. They hurt timing precision, since their discharge rate is faster than the larger value, and each station must be tuned. Effectively cost-prohibitive in our particular niche. 

When Jim was developing the SE, Gary and Rob report that they listened to and measured many, many configurations of bypasses and brands of caps including darling  audiophile cost-no-object ones. They chose the then-best Clarity SA for its rightness, both measured and heard. The single (non-bypassed) value was chosen as sonically superior to the bypassed version. Note also that the CSA, with its copper spluttering, is said to be a league ahead of the ESA, which was a relatively small advance over the SA.

Beware that the incision of these higher grade components comes with its own set of potential perils. In Lexington last week I saw Rob's 7.2 XOs in which he had replaced all series feeds with ESAs to compare with stock. He (and his cohorts) preferred the stock parts. The point is that the whole thing is a pot of soup, and "improving" something may require other compensations. When converting Beetle's 2.4s, I was relieved that every upgrade resulted in upgraded performance. As he mentioned, his SE's were late Chinese manufacture with room for improvement by reverting to old methods, from which we also upgraded layouts and coils. All his parts were very carefully selected, and synergy ruled. My own path is with Mills resistors and Clarity caps on old-style point to point boards with new layouts and heat managemnt. I am considering those electronic upgrades as end of project decisions. My focus is on re-bracing and re-baffling which is progressing well.