2. amps-preamps
  3. 153086-109191

Problem with Ref 5SE

I recently purchased a 5se and took delivery the other day. Did not get a chance to open it up until last night. Upon installing it into system I switched it on and after it warmed up, I was very much interested in hearing how it sounded against my current 27. After listening to several tracks with the 27 I switched pre's and after a couple of minutes playing a CD I got some noise, almost a loud static sound coming from the right channel. It was not effected by changing volume controls or input selector. It went away after 10-15 seconds and then returned. At that point, as it was late, I shut everything down and figured I would take another look in the morning.

This morning I removed the top cover and pulled and reset the output tubes and then the power tubes. I fired it back up and still had the 'static' sound but now it also had a humm, like an impedance type hum and constant. I do not believe that the humm was present last night as it is quite noticeable. 

The static type load noise seemed to have abated after the unit warmed up after maybe 15-30 minutes.

Can I assume that perhaps a tube was damaged during shipping? Do you ARC guys think a new set of tubes will fix this issue or am I looking at something more severe? Any additional suggestions to try and pin this down?

I rerouted the IC going to the amps to get them further away from source IC's and no help...

I am a little bummed, as my initial impression it that it is a leap from the LS27, my current...
128x128stevea11757
stevea1298's avatar
stevea1298
48 posts
 
ghasley

That is a definite possibility, but will wait until the new tubes come in and try that, if sound remains I guess in it will go.

I did go back up late last night to see if it was something that I can live with, from listening position, once the music starts the 'noise' disappears and only reappears between tracks, even soft passages it is really not noticeable.  My speakers Shahinian Hawks are 87db with a nominal impedance of 6 ohms.

Previous owner has said it was dead quiet in his system.

I am going to hold off judgement until I get new power plant installed, then new tubes and then considering a aftermarket power cable, although the factory seems pretty substantial. 

Hopefully one of these will quiet the beast.

stevea1298's avatar
stevea1298
48 posts
 
BTW, anyone know of a ARC authorised service shop local  in NY?
testpilot
947 posts
 
Can you take the 5SE to a friends or a dealer (call first) and see if you can duplicate the problem.
chip_2950
12 posts
 
I have a Ref 5se and had a Ref 5.  Both were dead silent into multiple amps.  Speakers:  Martin Logan Summit x and B&W Signature 30’s.  Both very revealing.

Stupid questions:  Are you using the CD input and balanced interconnects?  Have you tried switching to an AUX input or single-ended interconnects, or both?
You did try both outputs, right?

IMHO.  I would stay with the stock 20 amp power cable.


tattooedtrackman's avatar
Ag insider logo xs@2x
tattooedtrackman
884 posts
 
I have had the 5se and now the ref 6. Both are dead quiet with and without stock power cord. I believe all of your tests you will do will be of no help. Tubes , power supply , power cord etc. I believe something happened in transit. Especially that the tubes were left in the sockets. That should of definitely not have been shipping like that. I also feel that there is absolutely no reason for u to live with your 5 se making a humming noise. I definitely would not live with that no matter how minor it is. Or that it only reappear in between tracks. There is absolutely no reason for that. Send it in to Arc for repair and get it back to normal operating condition. I would also contact the seller and tell him that he didn’t ship it the right way and see if u can work out something that it has to go into service for his negligence. Good luck. 
More to discover