A Worthwhile Untrasonic Cleaner

Quick update for any who maybe interested in going this route.

I think the rotisserie is very well made, the plastic label covers/ spacers seal very well with the silicone ring seals.
It’s a perfect fit on the lip of the US tank and slides up and down easily to dip the records in the tank.
Only wish would be for the motor to do both directions rather than the present anti clockwise only.

Tank works well enough IMHO, heats up quickly and drains very easily.
I heard a lot of complaints about excessive noise but obviously nobody works in my business... Lol.
I think is is very acceptable noise levels but I do have it set up out in the workshop due to the potential mess more than anything.
And I have a huge workbench I can spread everything out on with towels underneath all to protect.

Will it make as good a job as a $4k machine? I would say not but so it shouldn’t at over ten times cheaper!
I am all in at $360 USD.

Good time’s!

Thought I would update with some mods I made to cleaning regime with this system.

Increase temperature to 40 C.
Increase US cycle to 22 minutes.
Clean just 3 albums at a time, not 5. This gives an appropriate 1" gap between albums.

Noticeable reduction in background noise of the vinyl.

Takes longer but if a job is worth doing its worth doing right.

Enjoy!

Man this is like deja vu all over again.....

I spent well over a year researching the US cleaning thing and about 2 months ago had all my ducks in a row, took the plunge. I bought a cheap tank, 6L Chinese product that runs at 40kHz, 180W and would likely spring for something a little better but at $100 it seemed reasonable place to start.

I got the VinylStack 3 record but in retrospect, would have opted for the 4 record stack as it will just increase each cycle by 1 record and take no more time.

The formula was the most tricky part and on another forum, a gent who is a chemist has been entertaining questions and given learned answers for a couple years now. I thought that I would try a solution based on his and others recommendations which will hopefully cover most of the gamut of what we will run into as far as unwanted stuff stuck to our record grooves is concerned.

Here is the formula I am using and have found it to be very excellent indeed:

FOR A 10 GALLON MIX (8 TANK-FULLS AT 5 QTS. DISTILLED WATER PER TANK)
(I discovered that 5 qts. works perfectly in the 6 liter tank, fills nearly to the overfill line)

Triton X-100 50ml
Hepatstat 256 38ml
IPA (91%) 72ml
_________________
Total 160ml

Mix these ingredients in a container (I am using an empty IPA bottle).
You will need to refrigerate the Triton after opening as it is prone to growing bacteria otherwise. Once the Hepastat is added, no more worries and the solution can be stored at room temperature. Also, you will not be able to mix the Triton unless you have added the IPA as it is extremely difficult to mix unless you do.

Once you have the above ingredients mixed in your empty IPA bottle (or a bottle of your choice), add 20ml to each tank of 5qts distilled water. Then, ADD AN ADDITIONAL 200ml of IPA (91%) to the solution in the tank and you’re ready to go!  Once you start to see a lot of detritus in the bottom of the tank, it will be time for a refill.  Totally empty the tank, rinse well (I use the faucet in the kitchen for this) and dry (I use paper towels).  You still have 80ml of the mixture left, so enough to do 4 more tanks.....get the picture?

As mentioned, this formula is nearly identical to that suggested by the kind gentleman on the other forum who goes by the handle of Phantomrebel so giving credit to whence it is due.

The last step before you drop the records in on your VinylStack or other turning/holding device is to turn the US cleaner on for at least 5 minutes to allow the solution to degass.....you will achieve better results that way. I do use the VinylStack, as noted, and have it set to 6V that yields 1 complete turn of the record every 3 minutes. I set the timer to 15 minutes, which means 5 complete turns for that cycle. I set the heater to 30deg. C. but as others have noted, when the transducers are turned on the temperature will rise fairly steadily. I usually do about 9 records in a session (3 cycles of 3 records) and the ending temperature is about 42-45deg. C. I have noticed NO warping or other unhappy outcomes at these temperatures. I would suspect that the records at the higher temps (the last 3 cleaned) actually might benefit the most at the elevated temps.

Happy cleaning all.....and.....it really, really works! I’ve provided a couple friends here where I live with the details and they are just smitten at how clean and quiet their records are now.