How to guarantee to lower noise- ground loops in your system


I have been through many problem area where noise in the  audio chain was a problem.
my friend Who is a Electrician solved the problem . All too many times people add a dedicated 20 amp circuit 12awg is standard 11-10awg even better lower resistance , also most important 
you need a Isolated dedicated ground, this is totally insulated right back to the earth ground in the 
breaker box this will dramatically lower your noise floor and remove ground loop problems .many people just put a dedicated line and think 
that’s it ,not so, if you are going to go through the trouble, then  for maybe $100 more the isolated dedicated ground  to the dedicated circuit is a must. I can tell you without question .
my Audio has a noticably quieter background .in songs i now hear low level musical artifacts like reverb off a guitar fading cymbals and clearer seperation of instruments .well worth the effort .Hopefully 
this will help others .this is a essential system upgrade .
128x128audioman58
Several years ago I drove a new ground rod directly outside of my dedicated listening room, and connected an 8 gauge ground wire to an isolated 20 amp receptacle. That receptacle feeds my Pure Power 2000 a/c regenerator and also my APC S20 power conditioner. That isolated ground was the only ground wire for my stereo system, and did not connect to my electrical panel. It worked fine but I did not notice any great improvement in my sound. Maybe I might have noticed a greater improvement if I had also ran the neutral wire to the new ground rod, or maybe not.

About a year later I was talking to one of my new club members who had moved to Florida from north of Dallas Texas, and is an electrician. Since he is an electrician I told him what I had done for an isolated ground in my system. This is freaky, but he told me that he had done the exact same thing in Texas. His ground rod was struck by lightning, and traveled through the ground wire into his isolated ground receptacle, and also caught his drapes on fire.

It had previously been in the back of my mind that the same thing could happen to me, because we get a tremendous amount of lightning where I live. My dedicated isolated ground receptacle is also behind my drapes, and I do not want to remove the drapes because they run the entire length of that wall. So I removed the eight gauge ground wire and reconnected the ground wire that goes to my electrical panel.

In the future I may try installing a plastic box on the exterior wall by the new ground rod and leaving enough wire inside the box to reconnect to the ground rod for brief usage at times when I’m sure there will not be lightning strikes. This is entirely illegal and shows that there are solid reasons for electrical codes, and most of all to always pull an electrical permit for new electrical work. If you do not want your house to burn down do not try the above.


vv32bl
... I drove a new ground rod directly outside of my dedicated listening room, and connected an 8 gauge ground wire to an isolated 20 amp receptacle. That receptacle feeds my Pure Power 2000 a/c regenerator and also my APC S20 power conditioner. That isolated ground was the only ground wire for my stereo system, and did not connect to my electrical panel. It worked fine but I did not notice any great improvement in my sound.
That’s an obvious NEC violation and a potentially dangerous scheme, because a fault on the ground wouldn’t trip the breaker back at the panel. That’s why all grounds must be tied together with the neutral bus bar in the service panel.
To Cleeds,

Your response that me using a ground isolation receptacle and running the ground wire to an outside grounding rod does not sound logical that the circuit breaker could never trip.

My first house did not even have any ground wires, and I blew plenty of fuses in that house.  To this day you do not even need a ground wire between your electrical meter and the first electrical panel in the house.  Although you do need to run a ground wire from the first panel to any other panels.

Ok, I mentioned running the neutral and ground wires from that receptacle to the exterior ground rod instead of going back to the electrical  panel.  There was a 120v circuit between the hot from the circuit breaker and ground wire that ran to the exterior ground rod.  Can you explain to me why the 20 amp circuit breaker would not trip if the circuits 20 amp breaker was overloaded, other than it being a defective breaker anyway.  It does not make any sense to me that a not defective 20 amp circuit breaker could pass more than the specified amperage just because the ground did not go to the neutral or ground buss bars, that's probably rated for well over 100 amps  From your response above anyone that did not know any better would think that even with a dead short a non defective breaker would not trip. You are in essence saying that it would be like not having the circuit breaker at all

Sure, I know that in the rare case that an overloaded 20 amp circuit breaker fails to trip you would hope that the panels 200 amp main breaker would trip before the wire from the 20 amp circuit started a fire.

Either having a defective breaker or like I said previously lightning could, and has started many fires.


The previous comment by Cleeds is 100% correct. For further explanation see page 29 of the following excellent paper, written by a distinguished expert on such matters:

https://centralindianaaes.files.wordpress.com/2012/09/indy-aes-2012-seminar-w-notes-v1-0.pdf

Regards,
-- Al

To Almarg,

Ok, so you proved my point, because your illustration only shows a 5 amp current draw on a 20 amp circuit breaker, there in not any way 5 amps could trip a normal 20 amp circuit breaker.  Your circuit illustration defective equipment  would have to be connected either to a ground fault receptacle or ground fault circuit breaker to be correct.  Never have I seen any ground fault equipment in any ones audio chain. Ground fault receptacles are made for wet locations, so be careful whenever you touch anything connected to a live circuit.  Wear non conductive shoes and only touch these items with one hand.  If you do however touch an energized piece of equipment while barefoot, briefly touch only with your right hand while standing on your right foot, but it is not safe practice. 

Every preamp or power amp that I own has a tiny fuse of no more than five amps.  My power conditioners have 20 amp circuit breakers that will trip if there was somehow a dead short pulling more than the specified 20 amps.  If however there was a 5 amp short like in the page 29 schematic there is no reason that it would not be safely discharged to ground.