Kef 205/2

Edorr,
I run Hydra 2 for my mono blocks and I feel Shunyata doesn't limit the flow of music, etc. I'll look into PS Power Cords for the ARC Ref 3 and Primare CD31 as they are connecting to the PS Audio PPP.
I think the same brand conditioner and cables may work better

Has anyone listen to Grover cables? Grover allows in home trial so i've given a go and placed the order for a 6 ft pair bi-wired SC's. According to Grover, the high and mid cables will have a mix of silver, copper and titan wires. The low section will have copper wires

Hi Primare,
If you have your bass problem solved, groovy! If not, try the following.

Unplug one Kef205. Put your system in mono. Play test tracks from a test CD or test source (I use mac the scope/signal generator). Take a db meter and note the out put of the speaker at 100hz, 80hz, 63, 50, 40, 31.5, and 20. Make notes of the db readings. Now with out touching your volume control or settings, shut your amp off (Even though it is a MC501 a good idea), put your other speaker in the exact same position as the first speaker. Now run the exact same test and see if the speakers are matched or different. They may not be perfectly matched but they should be pretty close. You will be able to see if there is a speaker problem this way.

If your speakers are matched and playing low bass notes properly you can eliminate the speaker and move on to other issues such as positioning and placement. I have put a variety of speakers in the spot where my Merlins work best and the results were wildly different. In fact a very expensive set of Avalons sounded awful, yet positioned differently were amazing.

GOOD LUCK!!!!!!

Hi Primare and other KEf reference users, I just want to chime in here even though the post is old so I can share some of my experiences in cabling my KEF 207.2. here are the gears I use.

Pre-amp: Belles 28A
Amp: Belles 350a V2 in Mono config.
Cables: Speakers-Audioquest Redwood in Biwire with PSS jumpers, CD to Pre-Audoquest Wild Blue Yonder, Pre to amp- Siltech 770i, Power cables-mix of PS Audio AC5s (amps), and Oyade GPX (CD & Pre)
Power conditioner: RGPC 1280CE with JPS Labs AC Plus cord

I have tried many cabling options throughout the past year, and this is the final setup I settled with and by far, I think is the best setup I have established taking most out of the KEF reference 207.2s. I think the current setup sounds better than any dealer setups I have auditioned in my region. The KEF 207.2 when taken good care, can really produce jaw dropping sound but to get there, needs a look of tweaking.

First, you definitely need to biwire or tri-wire the reference line. When you do, forget about mixing different brands. Use one brand and if you bi-wire, get the jumpers from the same manufacturer as well and ditch the jumpers that come with the speakers. they are horrible. As shown in the manual, make sure to connect base section and high end section when bi-wiring, connecting jumpers from bass to mid. This approach produce much clearer wider soundstage compared to other connection options. I recommend against single wiring these speakers as you are not going to get the full benefits.

Second, I recommend you use the power conditioner but I recommend against the setup tha Primare origional posted. You need the CD and preamp going into the Hydra and amps going into the PPP if you are going to use this setup or you loose the top and bottom extension, at least in my case. However, I ditched this setup and finally got the RGPC 1280CE to condition all of my units. everything going through the RGPC. Some says it will kill the dynamics, make highs grainy, make bass too heavy etc. etc. and but that is just bunch of BS without having tried the setup truthfully. I found this setup to produce most pitch black background with tight bass without loosing the tonal balance, shrinking the depth or width or the inner details. If you are using the mono amps especially, I recommend RGPC setup. However, the RGPC nees to a good power cable as well. I use the JPS line.

I won't go into other cabling details since they are system dependent and we all have different individual setup at our home.

The biggest difference I saw in cabling is 1.Speaker cables (going from single to biwire-tri with good jumpers, when connecting bi-wire, connect to bass and high with jumpers going from bass to mid), 2.Power cables (use good decent power cables on your units including power conditioners) 3. Interconnects (makes least difference but if you have choice, use better interconnects from CD to pre-amp vs. pre-amp to amp)

KEF reference line possesses fine mix of American and british sound. They are transparent, hyper-extended with all the details you can ask for, throws a big soundstage, but also has that wonderful musicality making everything sound natural and real. They will allow you to listen to all types of music and make you feel that you are actually there at the front of stage.

Do give some time and sweat and you will be rewarded and will never want to throw them out into used market. The current reference lines are at the top of their game especially given the price points they are at.

Hi, I feel your pain. I bought a pair of 105/3's after hearing them at a dealer. best bass i ever heard, best everything, til i got them home. kef's r "user friendly", can be placed near boundries , I bought a db meter & stereophile test cd, & measured nearly flat all the way thru the freq range. hm. every other speaker brand out there boosts bass around 100 hz to get some deep bass.KEF dont. buy Stanley Jordan "flight of the cosmic hippo". compare your speakers, Bought mine in "90" they were a pain to get right but worth it.

Hi I know this is an old thread.

But I apreciate a lot the discusssions and i m a kef ref fan.

What the end of history, primare?