Phono Preamp. With transformer or fully active


What is the difference in sound between a fully active phono stage and one that uses a transformer for part of gain 

I read  discussions in External SUT’s being used and phono stages with built in transformers ?

I noticed that CJ Tea2 has two inputs one is with transformer & one is fully active ?

l also read discussions on fully active 
What is better?   Lol

is the sound softer, more detail , more soundstaging? Quieter?

jeff
frozentundra
I do not consider the use of the rather heavy secondary load in addition to a Zobel as a sonically acceptable solution.  
FWIW they *are* designed for that. I totally agree regarding your comments about bad core design- my comments  presume a decent transformer to start with :) ...   I think the 4722 cult has to do with a recording engineer named Eddie Ciletti.
Boy;

Who would have thought SUT’s are so controversial in application. My 2 buddies , that are LP guys, both have fully active with lots of adjustability.
Their systems sound superb, with a Lyra & Purpleheart cartridges 
I think it’s best to start fully active, as it appears
Being a vinyl , newby, 
Then listen and see how it goes

jeff
I might have been a little unclear above when I typed:

I do not consider the use of the rather heavy secondary load in addition to a Zobel as a sonically acceptable solution.

That should read:
I do not consider the use of the rather heavy secondary load in the form of a Zobel as a sonically acceptable solution.

I will add that the load from the Zobel is at higher frequencies only.

Jensen named the parts of the Zobel Rdamp and Cdamp which clearly tells its purpose. I do not know of any phono stage inputs with those parts intentionally in place. It would be interesting to see the response without the Zobel in place to see what it is hiding. I for one do not have a problem with a Low Q 2-5dB peak nearing 200kHz and find that any resistance or network added to tame it does more harm than good.  The 4722 or other vintage mic transformer turned SUT showing the peak in the 20-40kHz range is another situation altogether.

http://www.intactaudio.com/images/SUT%20white%20paper/4722%20vs%20emia.png

dave



Jensen named the parts of the Zobel Rdamp and Cdamp which clearly tells its purpose. I do not know of any phono stage inputs with those parts intentionally in place
I do, it retails for $3500 and has had stellar reviews.

It would be interesting to see the response without the Zobel in place to see what it is hiding.
It supposedly minimises internal ringing in the transformer.
If you simulate the load of the cartridge and run a square wave through the scope you can adjust the zobel to suit. In the afroementioned phono stage I have personally exerimented with altering the zobel to match the internal imedance of the cartridge, it is clearly audible.

The reality is that transformers are non linear in both amplitude and more importantly phase. It is the phase anomalies that kill the music - musical timing and natural harmonics are destroyed by phase anomalies.

In my experience, with an array of moving coil stepup devices to hand including both tube and solid state active, and many much vaunted transformers, is that active devices, for all their faults are more musically compelling.

Play any jazz record where there are changes in tempo within the track and a comparison between a competent active stage and a competent transformer will highlight the transformers destruction of phase and timing. Look at the bottom end in your graphs - its there for all to see.
I do, it retails for $3500 and has had stellar reviews.
Which phono stage is this?  

I agree with you on the phase issues and at some low and high frequency a transformer is going to shift phase and I think that the shift at high frequencies is much more of a concern than at  low.

 musical timing and natural harmonics are destroyed by phase anomalies.
yes....  bell labs found a strong correlation between phase shifts and voice intelligibility.  Higher order odd harmonics are dissonant to begin with, throw in some phase shift and i suspect they get downright ugly.
 Look at the bottom end in your graphs - its there for all to see.

I don't follow.  transformers like all systems have a finite bandwidth and with that they have finite linear phase.  It is much more of a struggle to  get a full 10 octaves of flat phase response out of a transformer than an active circuit so it becomes increasingly important to place the plateau of linear phase in the proper spot.

dave