Which vintage direct drive?


What's your preference of vintage direct drive, a Sony TTS-8000, a JVC/Victor TT-101 or a Pioneer PL-70, or for that matter, one that is close in used price? I can't afford a Pioneer Exclusive or a Sony PX-9.

My tonearm will be a Trans-Fi Terminator.

I am half-way tempted to use the drive unit of Dual 721 because I have heard that it is really good. 

Any thoughts would be appreciated 
enobenetto
The following is a extract from a Thread on another forum about the
Aurex SR-510.
It is a ongoing experience offered to the Forum Members about how Vintage TT's compare to known renowned DD's from the era, ones that when in top condition, have a reputation for being very capable and comparable to very expensive modern design TT's.

My Report on the SR 510 was about how the use of materials across the TT's compared, the following is a report on the Sound Quality comparison to another very respected Vintage DD.
If the OP wants the link to the full thread, they only need to ask.

__________________________________________________________


  since I don't have a SP10 at the moment, I can't make this comparison. But it plays at eye level with my Micro Seiki DDX1500 (also with TP92 tonearm), which makes the Toshiba (as a drive with a "good" tonearm) a bargain. I made the comparison with the spring-loaded Micro Seiki feet under the Toshiba. Since I don't have the original feet, I can't judge how big the influence of this line-up is. The DDX1500 is also equipped with spring-loaded feet.
My particular TT101 works on 120V or 100V as selected at the transformer primary. Yet it is labeled “Victor”. The acronym JVC doesn’t appear anywhere. I’ve read that it was made for sale to American servicemen stationed in Japan, but that’s just from one source.

It can vary from country to country, in Germany they are JVC as far as I know. Anyway my Japanese TT-101 now at JP Jones Workshop and it’s 100v.



Raul, There were 3 posts dated October, 2020, ahead of mine.  The last post before that was January, 2020, by Thuchan. Anyway, you know this is one of my favorite subjects, so I often cannot resist a comment on relevant threads.  On the DP80, if you use the manual speed corrector, it disengages the quartz-reference in the servo, so it is really a feature that one is best off to ignore.
Chakster, I would agree; by far the majority of TT101s are built to run on 100V only, but I have never seen one labeled "JVC" in lieu of "Victor".  I only noticed the 100/120 voltage feature on mine after I bought it.  Good that you have engaged the services of JP Jones, who fixed mine after 2 years of frustration on my part.  I "found" JP on a Technics SP10 thread; he has successfully built the SP10 integrated circuit necessary to run the Mk2 and Mk3, out of discrete parts that fit in the same space afforded to the IC, using SMDs.  Until JP made his part available, Mk2 and Mk3 users had to stow away old SL1200s, some of which also used this same chip for speed control, in case of chip failure. His home made chip is a bit more accurate than the original. Thus, although my SP10 MK3 was working perfectly, I eventually had JP install his chip into it. 


You may want to know that after JP found the fault in my TT101, it has run perfectly for the last two or more years. (The PCB was cracked, and the crack ran under a solder joint which covered the flaw, creating an intermittent problem.  Only a truly knowledgeable person would even think to look for it since it was rendered invisible by the solder and because of the intermittent nature.)  JP is simply "the best".

my TT 101 is marked Jvc and works at 220V it is a sampler version but I have seen some TT 101s sold in my country always marked Jvc at 220V.