OK - this may be the problem ...
- the Aria is not "grounded" via the mains cable
- it’s ground point is "relative" to the neutral side of its circuit - which SHOULD be at ZERO volts
- the images I have seen shows ONLY a 2 pin mains socket.
Even if there are versions with a 3 pin plug - the ground pin may not be connected to the neutral side of the circuit
This can present problems with certain amps - one I know for sure is NAIM - they design their components such that ONLY the source components provide the ground point and not the amp - so you get hum if the source is not properly grounded - as in this case
I had a similar issue with a "consumer grade" CD player and my NAIM amp
Any component that uses an "isolated" power supply design like the Aria may suffer hum issues (in some systems)
- Components that use Walwart power supplies can also create hum
There should be NO HUM at all !!!
The easy solution is - to make up a ground wire...
- connect one end of a piece of wire to the ground pin on a mains plug
- connect the other to the ground terminal on the Aria
- plug the mains plug into a wall outlet or power bar - whichever you use
- for best results use a spade connector on the end connected to the Aria
If that does not cure the hum you may need to ground the neutral side of your system...
- as before - add the mains plug to a piece of wire
- connect the other end to the neutral side of a cheep RCA plug
- connect the RCA to any unused RCA socket on only ONE of your components
- experiment with different components - it can make a difference
WARNING: - DO NOT GROUND AT THE AMP in this manner IF...
- your amp is a fully differential design (i.e. with balanced speaker outputs)
- in this case - ground at a source component ONLY
There could be hum due to a noisy transformer, but that’s a very rare occurrence these days - certainly not in most modern components
Proper grounding is essential in all systems, but for some reason designers seem to think isolated designs provide something superior
The debate between Isolated and grounded designs will rage on ad-nauseum
- the problem comes when trying to mix the two approaches in a single system
- then you may experience hum.
I’m yet to see/hear of an isolated design that works in EVERY system
In my case - even with my current Bryston amp -
- My Simaudio Moon phono stage is whisper quiet at full volume - it is a properly grounded design.
- However, - IF the Phono Stage is disconnected from the system, my Node 2i (with an isolated power circuit) will cause hum
- but grounding my system as above WOULD fix the issue.
- So you may only have to ground ONE of your source components !
ONE LAST THOUGHT - if the hum gets louder as the cartridge approached the motor, you may need to ground the motor - a common fix IF using a Grado cartridge on some Rega Turntables
ALTERNATIVELY...
- You could buy all components from a single brand
- that should work :-)
Hope that helps - Steve
- the Aria is not "grounded" via the mains cable
- it’s ground point is "relative" to the neutral side of its circuit - which SHOULD be at ZERO volts
- the images I have seen shows ONLY a 2 pin mains socket.
Even if there are versions with a 3 pin plug - the ground pin may not be connected to the neutral side of the circuit
This can present problems with certain amps - one I know for sure is NAIM - they design their components such that ONLY the source components provide the ground point and not the amp - so you get hum if the source is not properly grounded - as in this case
I had a similar issue with a "consumer grade" CD player and my NAIM amp
Any component that uses an "isolated" power supply design like the Aria may suffer hum issues (in some systems)
- Components that use Walwart power supplies can also create hum
There should be NO HUM at all !!!
The easy solution is - to make up a ground wire...
- connect one end of a piece of wire to the ground pin on a mains plug
- connect the other to the ground terminal on the Aria
- plug the mains plug into a wall outlet or power bar - whichever you use
- for best results use a spade connector on the end connected to the Aria
If that does not cure the hum you may need to ground the neutral side of your system...
- as before - add the mains plug to a piece of wire
- connect the other end to the neutral side of a cheep RCA plug
- connect the RCA to any unused RCA socket on only ONE of your components
- experiment with different components - it can make a difference
WARNING: - DO NOT GROUND AT THE AMP in this manner IF...
- your amp is a fully differential design (i.e. with balanced speaker outputs)
- in this case - ground at a source component ONLY
There could be hum due to a noisy transformer, but that’s a very rare occurrence these days - certainly not in most modern components
Proper grounding is essential in all systems, but for some reason designers seem to think isolated designs provide something superior
The debate between Isolated and grounded designs will rage on ad-nauseum
- the problem comes when trying to mix the two approaches in a single system
- then you may experience hum.
I’m yet to see/hear of an isolated design that works in EVERY system
In my case - even with my current Bryston amp -
- My Simaudio Moon phono stage is whisper quiet at full volume - it is a properly grounded design.
- However, - IF the Phono Stage is disconnected from the system, my Node 2i (with an isolated power circuit) will cause hum
- but grounding my system as above WOULD fix the issue.
- So you may only have to ground ONE of your source components !
ONE LAST THOUGHT - if the hum gets louder as the cartridge approached the motor, you may need to ground the motor - a common fix IF using a Grado cartridge on some Rega Turntables
ALTERNATIVELY...
- You could buy all components from a single brand
- that should work :-)
Hope that helps - Steve