compliance

bad news.. cantilever dislocated from rubber lol

Dear @anthonya : Don’s distress, here your new stylus replacement:

https://www.ebay.com/itm/AKG-Stylus-X25MD-24-Original-Stylus-NEW-FOR-AKG-P25MD-24/113325190186?hash=...

or this one, difference is about compliance only where this one is 35cu against the other with 24cu:

https://www.ebay.com/itm/AKG-Stylus-X25MD-35-Original-Stylus-NEW-FOR-AKG-P25MD-35/113325226128?hash=...

you can buy both.

and this a low weigth magnesium headshell:


https://www.ebay.com/itm/DENON-PCL-5-VINTAGE-HADSHELL/274701297619?hash=item3ff57927d3:g:6zcAAOSwvjV...


R.

I'm still happy. saved more than 500usd and earn some bragging rights.

I'm aware of the epc 205 issues. was told u can get jico ex and use in in mk3 or mk2L by jico. but technics already satisfy my curiosity.
also many people transplant jico ex into epc 100 easy to do

I have a good sample of Stanton 780 which I'm using now whic jico and retipping is easy, KenT mentioned it's almost same as original the jico replacement . 681eee with d1200 jico. 500al with original conical stylus.

most of this poor suspension can be solved by adding a drop of wintergreen oil let it soak a week and washed out with alcohol. 

was told my friend have Stanton 980 I will beg for it lol.. probably free. broken tip and get it rebuild 

Raul thanks for link, will get it. it's a great cart.. Best micro and depth is very clear. just worried another shot suspension. 

he said ok 980 is mainnnneee

Your Stanton will never perform as original Stereohedron if you will rebuild it, you need an original stylus with Stereohedron tip. When manufacturer is using aluminum cantilever the only benefit of this cantilever is press-fit diamond. When someone glue a new tip to aluminum cantilever it’s nonsense. So in case with aluminum you need a whole new cantilever with factory press-fit diamond.

If you want to rebuild then you have to send it to UK (Expert Stylus & Co) for Paratrace stylus tip. This company is very old and now specialized in Stanton service. Ask them: info@expertstylus.co.uk

You can’t transplant JICO SAS into Technics EPC-100 series, Jico is for 205 series and JICO SAS will cost you more than a better cartridge or very close to it. I’ve been using JICO SAS (BORON) long time ago on my 205c mk3.

In JAPAN ONLY Jico can retip Technics P-Mount mk4 series without replacing original Boron Pipe cantilever, but it’s for locals only (I have a bill from Jico for this job).

On Stanton you can use Pickering stylus, you need an original stylus.
If your model is Low Impedance then stylus from High Impedance is not compatible as far as I know.

The whole mess up with Technics cartridges is like knocking to the closed door or to a brick wall. You can simply use another enter quickly (another high-end MM cartridge).

My advice: stay away from any retipped or refurbished cartridges, it’s just a waste of time and money for nothing. Original cartridge (if it’s a good one) killing it!

The benefits of original Technics (impossible to find in good condition) is Boron Pipe cantilever and very low tip mass. Audio-Technics AT-ML180 has extremely low tip mass and hollow pipe boron (or beryllium) cantilever and MicroLine stylus. Grace LEVEL II BR/MR comes with Boron Pipe Cantilever and Micro Ridge Stylus! Those two cartridges are superior to original Technics for sure, I tried them all (original, not rebuilded sh**ty).