Hissing sound coming from tweeters


Right now I'm experiencing a hissing noise coming from the tweeters on my Klipsch RF7II's, and can't figure out what is causing the noise. It's almost like a white noise that is there when the amplifiers are powered on and is not affected by changes in volume.

My system consists of an Oppo BDP-83 blu-ray player, Ayre K-5xe preamp, and two Emotiva UPA-1 mono blocks. My cables are Audioquest King Cobra and Audioquest Emeralds. I would greatly appreciate any help resolving this problem. The hissing sound is very annoying. Thanks.
cfaille
Wow. You guys are extremely helpful and full of good ideas. Thanks for all the replies.

This morning I rearanged my equipment and made sure all cables, cords, etc. are nice and neat. Unfortunately when I powered everything back on the hiss is still there. I disconnected my XLR cables from the pre-amp and mono blocks again, and the hiss is much less noticeable. When disconnected you have to put your ear close to the tweeter to hear the hiss. When I have the XLR cables hooked up to the pre-amp in balanced mode the hiss is amplified.
When I have the XLR cables hooked up to the pre-amp in balanced mode the hiss is amplified.
Does engaging the preamp's mute function reduce the hiss level?

Regards,
-- Al
When hitting the mute button the hiss doesn't change. Neither does selecting a different input or increasing/decreasing the volume. I tried plugging the Ayre in directly into the wall instead of being connected to the Panamax surge protector, but the results were the same. When I swap the XLR cables for RCA cables the hiss is still present as well. I'm beginning to think that the Ayre just doesn't pair well with my amps.
I'm beginning to think that the Ayre just doesn't pair well with my amps.
Given the findings you've described, I suspect that you're right. When you connect the cables to the preamp, you are introducing the possibility of ground loop-related noise, but I would expect the xlr connections to be much less susceptible to that than the rca connections, and you are saying that the results are fairly similar either way.

So even though the noise performance of the Ayre preamp is probably very good (I note that John Atkinson describes the noise performance of the presumably similar K5-xeMP as "superb"), the little bit of noise it generates in the circuitry that follows the volume control is being boosted to bothersome levels by the combination of the high gain of the amp and the high sensitivity of the speakers.

The only solution that occurs to me other than replacing the amps or the speakers would be to put in-line attenuators at the inputs to the amps. The Rothwell's, which are available in both balanced and unbalanced form, are an example, although the 10db of attenuation they provide might not be as much as you would want. I believe some others are available that provide 20db or thereabouts, but I'm not sure if they are available in balanced as well as unbalanced form.

Regards,
-- Al
Sounds like it could be a ground loop issue.

You should try cheater plugs on the power cables. These are the 3 prong to 2 prong adapters found at hardware stores. Cheap and easy to try.

I keep a CleanBox II around to try to detect ground loops. It lifts the ground on the cables (source to pre or pre to amp) to eliminate ground loops. It takes a 1/4" TRS jack, so you will need either balanced or singled ended XLR/RCA to TRS adapters or cables (Monoprice has XLR to TRS cables). Since you have mono blocks you could do one side at a time, meaning fewer adapters to buy. It is not a long term solution, but it can help identify if there is a ground loop carried by the ground. CleanBox II is $35 to $55 depending on where you get it. Alternatively, if you can make cables, you can try making either RCA or balanced ones with the ground not connected, as a test.

Do you have any other pre-amp or amp you can test to see if you still have the hum issue? So, the Ayre with another amp or another pre with the Emotiva?