Amp recommendations for Tannoy Canterbury SE


I have just purchased the Tannoy Canterbury SE speakers and am driving them with my existing Ayon Audio Triton II KT88-based monoblocks delivering 100 Watts per channel. My only source Ayon CD-5 is connected directly to the Ayon monos, since the CD-5 has got a decent volume control. I listen to mostly very fast and dynamic music including rock, techno and others.

My initial impressions are that I am not getting speed, punch and tight bass. I am wondering if this is possibly due to an amp mismatch. While the tube amp's 100 Watts seem more than adequate for Canterburys 8 ohms and 96db spec, I wish I could get better results.

I am seeking recommendations on what could be the best suitable amp for the Tannoy Canterburies. I am open to both tubes and solid state.
- What could be some of the best Tube Amps as well as Solid State Amps that could be a good match ?
- Existing Tannoy Prestige series speaker owners - what amps do you use ?
- Should I be looking at tube amps which are based on tubes other than KT-88 ?

If you have any other recommendations in positioning/configuring the Canterburies please let me know too.

Many thanks in advance
Wilfred
wilfredt
Sksos1, you have pointed out another important area - the gain in the preamp. In my case, I don't have a preamp and also just switched from Ayon CD5 to Oppo BDP-95 to play directly into the amps. This could be a problem area too and I need to revert back to CD5 and play with the gain settings on the CD Player to see the effect.
'
IMO, the Canterburys sound pretty good set up any old way. But they do benefit from voicing, right down to very small adjustments.

It's unlike any other speaker I've worked with in that way.

Once broken in, they are so musically compelling, it's almost like, "why fix it if it ain't broke?"

But once they are dialed in, it's all over for most folks - their "desert island" speaker has arrived.

Re amplification, I've had good luck with amps in the 30 watt region, both SS & tube. The first pair I voiced a few years ago had a 60 watt amplifier on them.

I'd like to hear if a more powerful amp might sound even better but then we get back to "if it ain't broke..." ☺
.
Canterburys sound good with both solid state and tubes, imo. I wonder how a bi-amp configuration would sounds with tubes on the midrange/tweeter, and solid state for the bass.
I have been listening to Tannoy GRF Pro's and 15" Monitor Golds in Canterbury sized cabinets for over 15 years. In my view tubes are not the way to go - I've had Futterman OTL's, Quicksilvers, Conrads, EAR etc high power, low power , pentode, triode, ultralinear 6550's, EL34's, 8417's, 211's etc. The ear opening experience I had was listening to von Karajan's Beethoven 5th on the GRF Pro's with 500 watts of heavily modified Perreaux 5150B - as in the only thing original was the power supply and mosfets. Even though the speakers are hugely efficient the big power amp's headroom and control over the speakers clearly enabled the relentlessness of this performance to be communicated which I never previously heard. My supposition is that high power amps provide better control over the driver, Tannoys own reference amplifier was a 250wpc mosfet amp. I have come to the view that if you value speed and timing high current solid state is the way to go, I use a 50watt high current ss amp. I would look at something like MBL's or Pass Labs.
I would also echo the views above, speaker positioning and angling adjustments of even 1/2 an inch can yield significant changes in openness, balance and bottom end.
Hornguys, thank you for your response. Appreciate your inputs on couple of points :

1. I had initially toed in the speakers as per the manual in "intensity stereo toe in" mode or "crossfiring" mode. However, yesterday I followed the "Get Better Sound" book to toe them in such a way that they crossfire 1 feet behind listening position. Is there any recommendation on what is the best approach that works for the Canterburies ?

2. Are there any tips in setting up the fine tuning settings in front of the speaker ie "Energy" and "Roll off" ? I could not get much difference between these settings; perhaps bcos I didn't play the right music that covered those frequencies. In any case, I guess these are the final tuning parameters once the speakers are dialed in, correct ?

Appreciate your inputs.