Cartridge Loading.....Part II

@mijostyn  : " Digital is hear to stay .."

With out single dude. Good.

R.

 

 

For the record (if you see what I did there) I've never stated that loading a cartridge would cause mistracking! That is simply Raul with his usual logical fallacies again (in this case, the classic Strawman).

What I have stated is that loading the cartridge will cause the cantilever to become stiffer. This fact is unavoidable as anyone grounded in generator and alternator theory knows. This does not mean that the cartridge will mistrack. It means what I said: the cantilever will be stiffer; whether that affects the performance of the cartridge is another matter and other than suggesting that it might affect high frequency tracing ability. I've also been careful to not state what frequency, which may well be ultrasonic; at any rate obviously is an unknown.

Raul, in his on-going quest to simply make me wrong, has been trying to put words in my mouth. Fortunately I'm way to far away for him to actually do that 😁

@atmasphere 

I gave up when Raul confused cantilever material with cantilever motion ( see quote from Raul below ).

The reality is that any change of loading will possibly have an impact on "tracing the groove". The Shure white papers explain this clearly with their testing on groove tracing and the impact of changes in compliance - at worst they describe scrubbing motion of the stylus/cantilever from mismatched arms/cartridges. It is the genesis of the use of their stabiliser brush. Tracking tests on records do not measure distortion - they only indicate a tracking ability ( crudely ).

In my view there may be no obvious mistracking from altering the loading, but there is the possibility of a change in tracing and distortion ( for better or worse ). 

If Raul loads all MC at 100ohms, then likely he cannot hear the impact of changes in loading, or he has a low resolution system - or both.

As an aside I agree with JCarr's and your comments that loading is more about taming poor quality phono stages with poor overload margins at ultra high frequencies. Folk need to understand that, like brick wall filters in early digital, problems at ultrasonic frequencies can generate artefacts down into the audible region. Perhaps Rauls home brew preamp is in this group which would explain why he needs to load all MC's at 100ohms - which is extremely low - particularly for cartridges with an internal impedance above 5-6 ohms. It's no wonder that Raul thought for years that he preferred MM cartridges most of which have large phase shifts and frequency aberrations in the audible region - necessarily tuned by loading R & C of course in order to get a reasonable facsimile of a linear phase coherent response. 

 

I did it.Over the years participated in no less that 8 threads about cartridge loading here and wbf and in one of them I posted something as:

stifness of cantilever it's a good thing because cartridge designers normally looks for the stiffer cantilever material as Boron, higher stifness the better in favor of better quality level listening performance.

The distinction between virtual and actual ground is a subtle one.

When an opamp inverting input is used, the virtual ground is extremely similar to a real ground as the action of negative feedback makes it so. The difference is in the error term- i.e. the output voltage divided by the open loop gain of the amplifier, together with any impairments added by the amplification system.

This difference can be extraordinarily small, so arguing that the virtual ground is not a real ground is largely facile. 

As far as the source is concerned there can be essentially negligible difference between a real ground and a virtual ground.

Claiming, arbitrarily, that it is prima facie audibly different as far as the source is concerned is not reasonable. 

@wynpalmer4 The virtual ground is one thing when it is driven by a resistance in series with the input (which might be a cartridge). Its a bit different when the cartridge itself is that resistance. WRT actual ground, I think we can both agree that a cartridge driving a dead short will not produce anything that can be amplified. A virtual ground is different in that manner 😉

One thing that has come up in this thread is the mention of Lenz's Law, which has to do with the radiation of a magnetic field from a conductor when conducting. Its been brought up in the context of 'back EMF'. I've not been able to discern how this is supposed to work; if driving a loudspeaker (which has significant inductance interacting with a magnetic field) you do get back EMF but in the case of the cartridge an impedance (for the most part) very little inductance in the load is present. So I would appreciate an explanation; as best I can make out the back EMF would be insignificant WRT the source. 

Dear @dover : As always I respect a lot your opinions but what you are talking about me and my " audio life " trend certainly is far away to be reality.

If that’s really what you think then you are wtrong about and let me explain you:

 

no I don’t confuse cantgilever material with cantilever motion, I’m with @intactaudio on that issue , if cantilever goes stiffer that’s is a good thing but if the cartridge suspension goes stiffer then that is way different and in no thread/posts no one named " cartridge suspension ".

Wyn and PM proved that changes on loading develops IMD, as J.Carr posted too, but don’t cause mistracking and I agree ( not today ) but from several years now with.

 

@imhififan gaves me the advise to make loading changes tests and he and I did it. I did it with different cartridges and one of that cartridge was the Denon 103 that by coincidence was the one he choosed too and both of us with different room/system experienced no mistraking issues by loading changes.

 

 

 

I know perfectly the impact that loading has mainly in the phono stages and in way minor way the impact in LOMC cartridges.

You are wrong about my phonolinepreamp that is designed with a really high headroom and is totally inmune of those poor designed phono stages even that my preamp frequency goes over 1.5Mhz.

@lewm owns the same unit, please ask him. No I don’t need per sé to load at 100 ohms when almost all LOMC performs the better with that load, theory of loading cartridges is theor and we know that some times what theory says does not happens under play.

 

Wrong too that I prefer MM cartridges, it’s not that way. Several years ago and due that I owned some MM/MI cartridges that were in closet I decided to give a listen to it and then I discovered to me that with today room/systems MM/MI cartridges can play with high quality performance levels and from there came that very long thread on MM cartridges.

In the other side ( maybe you born in audio with a LOMC cartridge in your hand. ) my very first cartridges in audio were all MM/MI that were the ones I re-discovered several years later and my first LOMC cartridge was the same Denon 103 that I used on the loading tests. In those times I owned Pioneer top of the line electronics and its HPM 900 speakers.

 

Btw, I posted several times that I’m not against the theory of that stiffer issue and I don’t want to add more comments about when all is done by the gentlemans that really has the knowledge high levels and first hand tests about even one of them made several tests in other thread in the same loading subject in real time because he has the modeling tools for it: yes that gentleman is Wyn. Can you do the same with the same knowledge levels?

No one is perfect and certainly you and me are far away from there.

 

Btw, please don't follow try to hit me because you can't and I'm not like you and I'm not to start speaking of each of your system audio items you own, so stay calm and cool.

 

R.