Nearly all manufacturers do not advertise/exhibit their product measurements? Why?

@holmz

I felt there is no other way for you to get the info you were requesting about gear.

The measurements of the gear are different than the measurements of how the gear behaves in a room right?

That depends on if it is a signal measurement or a room measurement?
The former is an electrical thing for components, IC, speaker cables, amps.
The later is about fields, which are measurement of the resulting acoustic field… that combines the electrical signal with the speaker and the room.

To isolate and remove the room and speakers, makes it a bit easier to consider how each component, IC, cable etc is contributing or not to the overall picture.

The ICs will not really have a whole lot to do with the room, unless it is high inductance or capacitance and being use like a tone control.

If there is some other thing happening with crystal boundaries, or dielectric polarisation, then that too should show up as the signal being changed when comparing one IC with another.
When this cannot be shown, it leads me to believe that it may not be measurable.

 

I advocate getting the room right first and yes, in room measurements can indeed make the trial and error process a bit faster (and maybe even less expensive).

^This^ I can abide.

 

Now, to answer your question to the OP of how to separate the real deal from a fable I can’t tell you a single measurement that will get you 100% guaranteed satisfaction that your money was a good investment. If you know a better way than auditioning it in your own room I am open to trying it.

Well there is a null test, and ICs should respond well to that… and power cords should show that the signal coming out of say a power amp is either the same or changed if one can compare them. But this never seems to be shown. 

Speaker cables have inductance and capacitance, and the speakers have larger current demands than an IC. When a cable coma-any has specs that is great.
With, or without, that I can only assume that if I want the total inductance and capacitance to be low, then I should probably keep those cables on the short side.

I’ll likely stay with the IC mostly using Mogami/Neutrik  combo, and a few speaker cables of Magomi or cotton/.copper, and a few ICs using silver and cotton.

Most of my ICs are only as long as they need to be, and I would rather spend the money on electronics until such time as I can understand if the IC are different or not.
Better is good, but to begin with can we even know if they are different? 

 

I would not recommend just taking some expensive speakers that measure well and sticking them in a room with bare walls like some of our scientifically minded guests.

There are step function and impulse response measurements.
The FR can be largely corrected with DSP/EQ, and the impulse response somewhat corrected with Dirac.

Whether someone starts off with the room or speakers, they often often end up with both good speakers and a somewhat treated room.  More often than not the room work comes later… so there is no great dishonour in having speakers that measure better as a start.

It doesn’t matter too much how well treated a room is treated if the speakers have poor impulse response, poor frequency response, resonating boxes, being output limited by compression, and have high harmonic (IM, and Doppler) distortion… but the room treatment may help with their radiation pattern and remove some brightness from the FR.

 

For casual listening, fine. For critical listening and professional reviews maybe get some feedback from a knowledgeable third party like Anthony Grimani at www.sonitususa.com or Jeff Hedback at www.hdacosutics.net.

A lot of people start with a speaker in a room, and then go to DSP, Dirac, or RoomPerfect, and/or add treatments.

I guess this last part is what separates us?
Namely whether it is a for critical listening, or causally listening to music.
And then what are we critically listening for?

I often start out wanting to listen to music and get blocked by sibilance, and once the grating sibilance is gone, then I get happy again.
The recordings that are overly sibilant just end up staying in their sleeves most of the time.

Quick post answer (I haven’t read them all yet). @holmz

1. I didn’t know that he needed a new power cord but upon seeing what he was using, knowing friends negative experience and knowing my own experience with this particular high end cable, I suggested it. He didn’t believe in it as an electrical engineer but did a 180 after he heard it for himself.

2. As to the ragged frequency response so obvious in the bass, I had two friends accompany me pre-power cable change and the Golden Ear remastering engineer friend blurted out that it sounds terrible. He is high functioning slight autistic so he just let loose. We heard as well but didn’t know why with such great gear. Anyone could hear that the bass was not linear, but ragged going up and down the scale. It was a total mess.

You write like a know it all as well. Why don’t you take a leaf from the book of ASR member Matt Hooper/prof (here) and read his comments on subjective listening and opinion (even as posted on ASR). The link is on page 3 with his agreement with Audiogon members (eventually) at the bottom third of the page.

 

You write like a know it all as well. Why don’t you take a leaf from the book of ASR member Matt Hooper/prof (here) and read his comments on subjective listening and opinion (even as posted on ASR). The link is on page 3 with his agreement with Audiogon members (eventually) at the bottom third of the page.

Sorry if I offended you @fleschler maybe I am a bit on the scale.

I am setting up the system in a new room (new house), so maybe these questions I have should be worded more like questions than as statements

It is not like I have access to people than can come by and look at the power cords and know what to change.
And I certainly do not know it all, like in terms of being able to identify the power cord as a solution to the bass being rippled.

@fleschler 

2. As to the ragged frequency response so obvious in the bass, I had two friends accompany me pre-power cable change and the Golden Ear remastering engineer friend blurted out that it sounds terrible. He is high functioning slight autistic so he just let loose. We heard as well but didn’t know why with such great gear. 

You didn't know?  Every system, and I repeat, every system out there will have uneven bass response regardless of price once placed in a room.  Below transition frequencies of a few hundred hertz, the room dominates the frequency response of the speakers.  You can pour millions of dollars into electronics and speakers and it will not be fixed.

The cheapest and one of the most effect solution is equalization which sadly many subjectivists audiophiles don't deploy.  With it, you can pull the peaks down and not only make the response more even, but also reduce the distortion from the speakers.

You can attempt to use acoustic products as well but the wavelengths are so large and energy so huge that you can barely make a dent in it < 100 Hz.  By the time you put enough of them in there you room can wind up too dead which is unpleasant especially for acoustic/orchestral/big band music.

A power cord will do absolutely nothing for this as this effect (modal response).  Yes, you can imagine that the bass has gotten "tighter" post such a change but it is a false impression which disappears after the psychological effect of the change is gone.

If you disagree, post a before and after frequency response measurement of your room with or without your favorite power cable.  

If this knowledge is new to you, I highly suggest reading Dr. Floyd Toole's book: Sound Reproduction: The Acoustics and Psychoacoustics of Loudspeakers and Rooms

The book costs much less than the money that was wasted on said power cords.

@amir_asr

After having read your reply and getting past the fake outrage, your answer is "No." , you do not check. That is alright, but it will always leave you open to questions.I say fake outrage because no allegation or insinuation was made; a simple question was asked. I could say that you protest too much.

Now some advice for you. If you got off your high horse and allowed some discussion in ASR, none of these threads would ever have materialised. It is your arrogance and intransigence in throwing off anyone who disagrees with you that annoys many people including your own minions. Look at your appalling treatment of restorerjohn, (yes I know you did not ban him, but you dismissed him in a particularly nasty way), on your own site. This was a disgrace.

One final point. :You stated: "Keep in mind that these are not mechanical product subject to large variations. Yes, there can be minor differences in performance of components but nothing significant can be achieved."

Amir this is blatant nonsense. Are you saying that adding better quality capacitors, improved shielding,  an improved power supply, high voltage transformers and decoupling the power supply does not lead to a significant improvement?