Speaker cable lifters.


Hey gang. What are your takes on speaker cable lifters ? Is there any truth to this ? I was thinking about purchasing some for my Straightwire Crescendos. Which are very thick speaker cables btw also. Diameter is over 1 in. Also my B&W 800 Matrix speakers are also quad wired so there are about 2 speaker cables for ea speaker that sits on top of the other. Would that matter ? Thanks in advance. 

128x128Ag insider logo xs@2xtattooedtrackman

@tablejockey I agree, that getting the room set up to be a very good interface for the produced sound energy is a high importance.

Looking at the OP's set up, there is the possibility such a practice of getting the room set up to interface with the Speaker is addressed.  

As energy is always transferred, it is best to discover the methods that can be adopted to transform the unwanted energies into a form that has the least least impact on the quality of the Sonic being produced.

The interest in audio equipment will nearly always lead to investigations about how to eek the betterment, even the smallest of change, if seen to be resulting in a betterment, can end up being sought by certain individuals.

When I suspended my Speaker Cables with a Cotton Thread, they were no longer in contact with anything but the Terminations and Cotton Material.

Did suspending the Cables make a difference? It is not certain, but there are Cables in use that are in free space, and when I tidied up the Systems Cable Loom,  ensuring that there was a minimum of crossing over cables such a Power, Interconnect and Speaker, the improvement in the sonic produced was very noticeable.

Again something that can be achieved for next to nothing in monies outlaid, and highly recommended to take the time to put into practice.         

I use my own homemade cable lifters.  I start with ceramic isolators that I bought at Tractor Supply supported by small bungee cord stretched over two wooden dowels.  The base is a flat square of wood that supports the dowels.  Very effective and after staining they don't look bad.  My cables are about 5" off the floor.  I made  8 risers for the speaker cables and 16 risers for my interconnects from the preamp to the amps.  Power cords rest on the previous wooden blocks, which are lower to keep them from touching the speaker cables or interconnects where they cross.

I experimented some years back with wooden bowls that we had.  I heard a difference so I cut of some lumber into wooden blocks.  From there I came up with my design using the ceramic isolators.  Not as techy looking as those AQ cable risers but much less expensive.  My design idea was to use the bungie for mechanical isolation and the ceramic and wood for static/electrical isolation.

I originally had carpet.  When I installed the hardwood floor I kept the cable risers in place.  I have never repeated the listening tests with and without risers on my hardwood floor.  You know, if it isn't broken, don't fix it.

@tattooedtrackman - the answer depends on

  1. your cables -
    • you said they are thick,which suggests a complex cable geometry
    • They probably take into account the effect of different floor coverings
    • I doubt if risrs would make any improvement
  2. your floor covering
    • if you have hardwood without any soft covering then risers would probably make little difference, depending on the cable
    • Carpe or rug - wool is best (see below)
  3. your floor - wood, concrete, ceramic
    • eithere of these woud probably not impact your sound

Man Made fibers are the worst and putting some air between the cables and the floor convering may be beneficial (depends on cable geometry)

I made my own from chlidrens alphabet blocks (from a dollar store) glued to a small cereamic tile for stabiity. on opposite sides I glued two pieces of craft sticks to hold the cable in place.

  • the tile is 2" square and bought in a sheet for a shower floor - from home depot

Not the most elegeant solution, but people like their simplicity and being wood/ceramic does not impact performance.

They made very little difference from when the cables sat on the broadloom, but my cables are not prone to the type of interference that can occur in this situation.

I’m all about keeping costs low and looks are not important, so the blocks were ideal for me

I would not place bi-wired cables on top of each other - try to seperate them by about 2 inches

Regards - Steve

 

@williewonka   Hey Steve. Thank you for your input. I appreciate it and maybe I’ll try something like that and make my own. 👍