300b lovers

The self-bias cathode resistor lets you choose anything between 6L6, KT66, 6550, and KT88. So far, the KT88 is winning, but the KT66 is very good also. We're shipping them with a matched quad of KT88's, but the user can use any matched quad in that family ... including NOS unobtainium tubes if they choose, because the operating point allows a life in excess of 10,000 hours.

I was reflecting on this approach vs simply using them as output tubes. Thanks to the gain of the 300B's, they're only using 1/3 to 1/4 of their potential swing, and the 300B's completely isolate them from the speaker load. So the only "load" is the 60 pF Miller capacitance of the 300B grids, not a loudspeaker. This puts them in the most linear operating region since they are essentially unloaded triode-mode power tubes, very different than the heavily loaded Class AB ultralinear of classical Golden Age amplifiers.

Good to see someone designing this way, I see too much premature tube death from a lot of high end audio designs.

If we chose, we could have a switch that would alter the quiescent current for the driver section, so 6V6’s could be accommodated as well. All of these tubes have the same pinout, but the optimal current for the 6V6 is in the 25~30 mA range, while the 6L6 and KT88 are happiest in the 50 to 65 mA range. (By comparison, the optimal range for a 6SN7 is 8 to 10 mA per plate.)

If the switch is in the wrong position, the 6L6 and KT88 would be under-biased and have increased distortion, but no harm done. If it is the wrong position with 6V6’s installed, though, they would burn up in minutes, and if one shorted, would take out the interstage transformer as well. So a visit back to the factory, all from one user mistake. You don’t want to give the user the power to damage the amplifier, just from a single switch setting.

A limited range switch to trim between 6L6 and KT88 would not harm either (in the wrong position), so that’s an option. But optimizing current for the KT88 still gives plenty of current for the 6L6, and we’ve found these types aren’t all that sensitive to current settings, just so long as there is enough.

A general rule-of-thumb in vacuum tube design is setting the plate dissipation somewhere between 50% and 75% of max rating, with 65% to 70% usually considered a good balance between tube life and overall performance. Unfortunately, many KT88 amps take the tubes right through their ratings, so new types like KT120’s have been created for these amps.

Let’s do a little quick math to see how hard the driver is working, compared to an output tube. The gain of a 300B is 3.9, according to this Western Electric data sheet. The interstage transformer has a moderate gain of 1:1.2, so the net voltage gain of the output section is 4.68. In power terms, that’s a ratio of 21.9, or 13.4 dB.

The driver is working at 0.2137 times the voltage swing of the output stage, into an open load that only has 60 pF of capacitance, and only draws current when the 300B grids pass into the A2 region at 80 volts swing. The driver can push the 300B grids at least 20 volts positive, and surprisingly, the 300B remains linear in this region, with no visible transition when it goes from A1 (negative bias) to A2 (positive bias).

There are no charge storage effects, unlike conventional RC coupling, so the transition between A1 and A2 is seamless, and recovery is immediate on departure from the A2 region. In addition, if there are any nonlinear grid impedances from the 300B as the drive voltage goes up and down, it is swamped by the orders-of-magnitude lower plate impedance (700 ohms) of the driver section.

There are further subtle benefits of transformer coupling. The 300B grids do not go into the positive-grid region at the same time: they take turns. This means both driver tubes are available to drive whichever grid needs current, not just one. And the paired drivers aren’t just paralleled, but in a Class A balanced circuit, so most distortion is cancelled.

This is important with an output tube with distortion as low as the 300B; the driver should be as clean as possible, yet capable of peak-to-peak 200 volt swings. At 30 kHz (which is a 38 V/uSec slew rate).

Last but not least, although four driver tubes are required, they don’t have to be matched quads. Matched pairs are fine. It doesn’t matter if the drivers in one amp are at 50 mA each and the drivers in the other amp are at 55 mA each. The difference can’t be measured and won’t be heard.

So if you have a stash of priceless MO-Valve KT66’s, which were manufactured in matched pair sets for the amps of the day, go ahead and use them! They will be operated very conservatively (far more so than most power amps).

There are a pair of pin jacks on the top panel to check if plate voltages match. Measure across the pin jacks with a basic DVM, set the DVM to measure DC, and if you see 3 volts or less, you’re good to go.