Praise for DacMagic

NOW - MAKE IT SING - like a much more expensive unit !!!!

Before I start - make sure you read the WARNING!

OK - Had this unit for a while now and been happy with it - especially streaming via an Apple TV - better sound than my CD!

But I had noticed that the unit and power supply runs a little warm - that usually means it's being taxed a little.

So I started looking at upgrading the power supply, which is not easy since all third party units are generally DC and this requires AC!

Then I had a moment of enlightenment - LOW VOLTAGE LIGHTING!

They use a 12 volt supply - only thing is, the units you can buy (for the garden) have timer crap on them

WARNING: DO NOT - I repeat DO NOT use the latest "electronic transformers" being used in the lighting industry - because they may not produce a true SINE WAVE!

If you can find a proper electrical supply store you can buy IRON CORE lighting transformers - mine is rated 100VA and comes with a heavy steel enclosure approximately 3x6x2.5 inches.

You then need some 16 gauge copper wire and a DC connector (it;s what those little plugs are called). I also included an fuse in the 120v side

Whole thing cost about $50 + my time - but the difference in the details and soundstage was incredible.

Now I'm not sure why CA does not provide a larger power supply - it would cost them peanuts. guess they want to sell you higher end product

REPEAT WARNING: DO NOT - I repeat NO NOT use the latest "electronic transformers" being used in the lighting industry - because they may not produce a true SINE WAVE!

Torroidal transformers would be even better since they are more efficient and far less noisy

Yes, it hums a little, but once I placed some plastic foam under the cover and some rubber feet it was not detectable from my armchair.

This is by far the enhancement with the largest impact I have ever made - like stepping up to $5000 cd player.

Spacious sound, incredible imaging in 3D, amazing details never before heard

I used the power supply from the DACMAGIC on my CA 640p phono stage and guess what - similar improvements we attained!

Both these units needed... MORE POWER!

Riley804 thought I should include the following to address concerns about messing with power supplies...

A piece of equipment will only draw the power it has been designed to draw - increasing the power rating of the supply will NOT affect this - increasing the voltage will!

e.g. In north america small appliances of different power ratings are all connected to the same power supply - which is generally rated at 15amps - my alarm/radio does not draw 15 amps - probably closer to 0.5 amps, but it is perfectly happy connected to a 15 amp service :-)

Also - if your power supply is rated at 1 amp then you assume that's all it will draw. if it draws more than 1 amp, then the power supply will overheat

Most ratings are continuous, but with hi-fi you have to be able to handle serious peaks in the music and if your power supply cannot do this then you get heat generated, which in turn, causes a whole host of other problems.

All I have done is provide a supply with a higher current rating so the equipment can now handle those peaks - that is all!

Another thing I found is that the CA power supplies were not very accurate - the phono supply measured 16+ volts and the DACMagic measured 14.5 volts

Also - the 22 gauge wire on their supply is no where near large enough to handle the continuous and more importantly peak current draw of this unit!

The new supply I am using measures 13 volts - which is much closer to the 12 volt spec

One thing I have found is that the DACMagic runs considerably cooler with the new power supply - and that is goodness for a unit of this power rating.

Why? - it is likely that the circuit is now getting the current is requires in order to operate as it was designed and is not in a continual state of "stress"

Using an underrated power supply to restrict performance, as appears to be this case, is very dangerous - a fire hazard!

Granted - CA does not want people messing with power supplies...
1. because most people have a complete lack of understanding regarding power ratings - an underrated supply becomes a fire hazard
2. the consequences of putting an incorrect type of supply on equipment would be damaging - The reason for my "WARNING"

They have a blanket policy - Don't mess with our supplies! - it's just so much simpler than an explanation!

What I cannot understand is why CA limits the electronics that has such great potential if properly supplied with power - probably cost related, but could be, they wanted to reign in the performance of this unit so it does not compete with their more expensive line. Guess what - it competes!

This unit is sounding far from stressed right now :-))

BTW - I would caution that you DO NOT try this unless you are adequately experienced - failing to take the proper precautions can lead to equipment failure or worse - FIRE!

Be careful if you are attempting this.

ALSO - because of its size (i.e. Small) connecting the DC Connecter plug required me to insulate the wires inside the plug cover with shrink-sleeve to prevent a short circuit - FATAL!

If you try this - you do so at your own risk!

Electricity is quite simple - unless you cock-it-up!

Wow! That is really fun news and a fun project. What are the model/part numbers of the parts? Any need for soldering? How about peak current? (I have all my audio devices plugged into the same 15A outlet.)

Soundbit - RE: same outlet - there is not problem with this - actually it would be preferable to prevent the dreaded earth loops

There is a taylor made ps from Pangea that is built for this type of upgrade - I would recommend their solution over the DIY one - since they are the pro's

see
http://www.audioadvisor.com/prodinfo.asp?number=PGP100

Even at $100 it will make you Dacmagic sing!

Happy listening

UPDATE: another AG member is using a ready made power supply

http://www.audioadvisor.com/prodinfo.asp?number=PGP100

It's a bit moe expensive, but professionally made by a reputable power company

If I had found out about this I would have gone this route simply because of the hassle soldering the silly little DC connector

I like the look of this unit very much because they have tackled all of the problems and then some including noise filtering - something my solution does not

I would advise going this route

enjoy