2. analog
  3. 1117142645

TriPlanar Tips

The manual that comes with the TriPlanar Mk VII tonearm is fairly complete, but there are a few things I’ve learned only by living with the arm. Note: I do not know which if any of these would apply to previous versions of the arm. My only experience is with the Mk VII.

1. NEVER raise the cueing lever while the arm is locked in the arm rest. This pressures the damping cylinder and could cause a silicone leak. For this reason and also for safety, whenever the arm is in the arm rest the cueing lever should be DOWN. This is backwards from most arms and takes some getting used to.

2. If your Tri-Planar doesn't cue straight down there's a quick fix, which may be included on some new arms. The problem is insufficient friction between the arm tube and the hard rubber cueing support bar. Just glue a bit of thin sandpaper to the underside of the arm tube. Make it big enough and position it so it hits the cueing support bar at all points across the arm’s arc. (Note: after doing this you will need to adjust the cueing height, see Tip #3.)

3. When adjusting cueing height (instructions are in the manual) always do so with the arm in the UP position. This adjustment is VERY touchy, since the cueing support bar is so close to the pivot. Be patient and be careful of your cartridge. (Note: after doing this you may need to adjust the anti-skate initiation point, see Tip #4.)

Chris Brady of Teres told me of a way to improve cueing even more by re-shaping the cueing support. Moving the cueing support point farther from the pivot improves its mechanical advantage and makes the cueing height and speed adjustments less touchy. This mod is easier than it sounds and requires only a length of coat hanger (!), but I don’t have pix and haven’t yet done it myself.

4. Changing the cueing height affects the point where anti-skate kicks in. (Yes, it's weird.) Once cueing height is satisfactory, adjust the short pin that sticks out of the front of the cueing frame. That pin controls where the anti-skate dogleg first engages the knot on the string.

5. The Tri-Planar comes with three counterweight donuts of differing masses. Many cartridges can be balanced using either of two. The arm usually tracks best with the heaviest donut that will work, mounted closer to the pivot. Of course this also reduces effective mass, which may or may not be sonically desirable depending on the cartridge. It also leaves more room for Tip #6.

6. For fine VTF adjustments don’t futz with the counterweight, there’s an easier way. Set the counterweight for the highest VTF you think you’ll need (ie, close to the pivot). Pick up some 1/4" I.D. O-rings from Home Depot. To reduce VTF a bit just slip an O-ring or two on the end stub. Thin O-rings reduce VTF by .01-.02g, thick ones by .04-.05g. Quick, cheap, effective. (For safety, always lock the arm down while adding or removing O-rings.)

7. When adjusting VTA, always bring the pointer to the setting you want by turning it counter-clockwise at least ¼ of a turn. This brings the arm UP to the spot you've selected, which takes up the slop in the threads. You can easily feel this happening.

Hope someone finds these useful. If you know any more, please bring ‘em on!
dougdeacon
sirspeedy
738 posts
 
I have to give kudos to the non damping crowd,wheter it "is" in the bearing or not(as in trough...a total NO-NO).

I have a group of pals who will not touch an arm if it requires "any" kind of damping!....Bearing or an external trough!!

From my experience with a Graham 2.2 and Phantom I,and II.....the pivot bearing certainly had it's own "signature",regardless of how much, or little fluid was needed.The results were absolutely superb,but there was always a "something" going on with any fluid addition or subtraction.

Though the results were superb,I always wondered how much more could be had without any fluid,if that could be the case(this was a NO-NO on the Grahams).

I finally gave up,once it was demonstrated enough times,on a "measely" VPI 12.6,using NO fluid anywhere(the "measely crack" was just kidding,because it is quite superb,and the arm replaced an Air Tangent linear masterpiece).

I'm going to assume that the latest Triplanar arm is about as good as is "really necessary",and should suffice any realistic assumption of what should be had from an LP.

If I were to buy any current arm(not any time soon,due to my daughter's upcomming wedding....OUCH)the TRI would be high up on the list.

Regards

krisgel
28 posts
 
? about removing the dampening trough: Do you also remove the flat metal bar that the trough attaches directly to? Also, it looks as though you definitely have to remove the arm from the armboard (Teres) to remove the dampening trough. Correct?
thom_at_galibier_design's avatar
thom_at_galibier_design
729 posts
 
Yes, you have to unmount the arm to remove the trough, and yes you want to remove the support bar. The idea is to eliminate a vibrating tuning fork. You'll be removing two small, straight slotted jewelers' screws.

Store everything in your Tri-Planar box in a small, ziplock baggie and SAVE it. The serial number is engraved on this support bar.

I recently added a setup page to my Tri-Planar section - for the Artisan Cadenza cartridge which you may better know as the Benz Ebony S-Class - http://www.galibierdesign.com/prd_triplanar_setup_art_cadenza.html.

The idea behind this series of pages it to document my experiences with the setup of various cartridges - to at a minimum give you a starting point for your journey.

The Tri-Planar (with its three ancillary counterbalance weights) allows you to fine tune the effective mass of the toneaarm, and this can have it's benefits if you avail yourself of this feature.

Benzes have always worked better on the light side of the effective mass scale - in the context of a Tri-Planar arm as well as in my experiences with the Moerch DP-6 (precision red arm wand).

This is accomplished by selecting heavier counterweights so that you end up with the weights located closer to the bearing pivot when you've set them for the appropriate tracking force.

In the case of the Tri-Planar, this means using the main (large) counterweight in conjunction with the largest of the three ancillary weights.

Fine tuning like this is one reason Raul will correctly tell you that there are some arm/cart combos that work magic, while others don't. Fortunately, with the Tri-Planar and Moerch, we have a better chance of achieving a successful match.

My apologies for the photo quality on some of the other cartridges' web pages. As time permits, I'll return to them - applying my improved lighting setup and photo skills to documentation of the other cartridges.

Oh yes ... should you lose the link to this thread, I maintain it at the bottom of my Tri-Planar setup tips page - the general page which is not dedicated to any specific cartridges.

There's some good information in this thread, and I wanted folks to have easy access to it.

Cheers,
Thom @ Galibier
paperw8
165 posts
 
As to suggestion #6:


6. For fine VTF adjustments don’t futz with the counterweight, there’s an easier way. Set the counterweight for the highest VTF you think you’ll need (ie, close to the pivot). Pick up some 1/4" I.D. O-rings from Home Depot. To reduce VTF a bit just slip an O-ring or two on the end stub. Thin O-rings reduce VTF by .01-.02g, thick ones by .04-.05g. Quick, cheap, effective. (For safety, always lock the arm down while adding or removing O-rings.)

I don't understand why you are using o-rings when it is easy enough to use the counterweight system to make fine VTF adjustments. You should have a small weight that screws into the end of the tonearm. The way to make fine VTF adjustments is to unscrew the small weight when you want to decrease VTF and screw in the small weight when you want to increase VTF. I haven't had any difficulty making fine VTF adjustments using this technique, and it seems easier to me than slipping on (and off) o-rings.
paperw8
165 posts
 

12-06-09: Thom_mackris
Yes, you have to unmount the arm to remove the trough, and yes you want to remove the support bar. The idea is to eliminate a vibrating tuning fork. You'll be removing two small, straight slotted jewelers' screws.

From my perspective, I would say that this idea of taking apart the tonearm to remove the trough is very inadvisable. First, the trough and support bar are VERY rigid. Second, to test my intuitions, I did an experiment in which I tapped on the trough with a screwdriver to test for resonances. There were none. The trough and support bar is no tuning fork.
More to discover