Worth having my SOTA Sapphire refurbished?


I own a vintage 1986, SOTA Sapphire turntable, fitted with a Linn Basik tone arm, with some sort of old, Audioquest cartridge (it has a red housing). After a lengthy remodel, I am finally getting ready to unpack my stereo system once again and get it set up. I have miles and miles of beloved vinyl. :-) My listening room is on the small side. I value transparency and imaging over sheer volume.

Associated equipment includes a PS Audio Elite Plus integrated amplifier (I think it has 70 W per channel). I recently sold my old Vandersteen 2C speakers here on Audiogon (for space reasons in the new house) and am looking to replace them with Regas or Paradigms, probably monitors (but that a whole other question)!

Anyway, the SOTA probably needs some inspecting and tuning. I think that the motor and bearing are okay, but I'm guessing that the suspension springs need adjusting or replacing; I think they're a little stretched out.

SOTA has an inspection and tune-up/repair service. Have any of you ever used it? I'd have to ship the table off to them, and, apparently, pay for return shipping as well (I do have the original box) and the table weighs around 50 pounds in the box.

By the time I do all of this and buy a new cartridge, to boot, I'm looking at quite a chunk of change. Do you think I'm better off selling the SOTA and putting the money toward, say, a new Rega P2? Please, no flames; I've been out of the active high-end scene for many years, so I have no idea how those tables compare.

Anyway, all advice appreciated.
rebbi
Rebbi, comments on two subjects for you.

First, your SOTA. I'll cast another vote to keep it. There are a couple of tests you can perform so that Kirk and Donna can advise you. For your bearing, remove the belt and spin the platter by hand. Put your ear directly over the spindle and listen for any sound (an inexpensive stethoscope from a medical supply house can be a great audio test tool, in this case applying to the top of the plinth). If it is quiet, note how long the platter spins after your manual start. If your table is noisy, does not spin smoothly, or does not slow down gradually, it is likely you have a bearing problem and will need to send it in.

Concerning your springs, the sprung plinth within the frame should hang the same distance below the frame on all four sides. I believe this distance should be either 1/8 or 1/4 inch. Kirk can verify this. If your springs are bad (stretched), you have a couple of options. A few years ago I bought a used SOTA Sapphire which seemed to be slightly loose so I disassembled the whole thing, filled the screw holes, and reassembled. If you feel mechanically inclined enough to do this, you could remove your springs. Then you can either buy new springs from SOTA or have your springs re-tempered (there is a how-to post on this on either A'gon or Vinyl Asylum). If you're not up to disassembly/reassembly, SOTA can perform any restorations necessary.

Second, addressing your speakers in your new, smaller room. Since you liked the sound of your Vandersteens, you might consider buying Vandersteen VSM (surround) speakers to hang on the wall. Because they are bass limited, adding one or two Vandy subwoofers can provide a more balanced, full range sound. This could achieve three features: 1) retaining the Vandy characteristic sound with speakers designed to perform from the wall, 2) good WAF because they are on the wall rather than placed out in the room (where most small monitors perform best) and they are available in white or can be painted to better blend in visually, and 3) because they would be out of the way, your room can more easily double as a guest room without needing to move anything before and after your guests.

Good luck.
Well, don't count the Sequerra Metronome 7.7 Mk6 out just yet! It's true that Acoustic Sounds no longer carries them, and when they did, the $1500/pr price put them out of your budget. But now, according to this Web page these little time-aligned speakers are available factory direct for $850/pair. And note the 3/03/08 date stamp at the bottom of this web page, so I guess this is current information.

Call or email and see what happens.
I had exactly what you ask about done recently. As mentioned, they do a great job and brought mine up to SeriesV (i think). I also went with an Origin arm and couldn't be happier. The rest of the system is mega-bucks and I find the Sota holds its own with anything even remotely close in price and is even more than I had hoped for in the new vinyl age. Enjoy.
>>very reasonably priced for what one gets...which is basically a state of the art product!<<

That's partially correct. All of their tables are reasonably priced and high value for that matter. Far better than VPI for the money.

However, "state of the art" is really a stretch and a bit of hyperbole.

Or unawareness.
Or its opinion Bill......just like your offering was an opinion............WHAM:)!