Reel tapes recommendations

.
Glai, there is no work-around. That's why all of my tapes were ruined. I had the big ten inch reels that took forever to play in either direction. So, I used the fast forward and the rewind, both of which were high speed. Does your rewind move at a slow speed? You could use rewind if your machine has a slow rewind. Slow winding is the only way to get the tapes to wind evenly. I didn't have the patience to wait three hours for a tape to wind slowly. Had I known that high speed winding was going to cause print through, I certainly would have been patient and wound them slowly.
.

Thanks guys. I just play the TP tapes thru so they can be stored. Good thing they run at 15ips. It sure is PITA but preserving those tapes are definitely worthwhile.

My serviced Studer A810 so far has not blown my vinyl rig away. The pitch stability, low noise and the front to back imaging are better than vinyl. However, it is not as transparent. I think the bottle neck may be the tape head or the old circuitry.

Is it better to stand the deck up or put it flat on a rack?

.
I don't know which is better, but standing up looks cooler. You also may want to check the back of the unit. If it is vented for cooling through the back, it may be better to stand it up. Also, some units have feet on the back of the unit, if it has feet on the back, it means the unit can be played on its back without problems.
.

Congratulations on getting into the RTR sound with TTP and a Studer A810. Both are quality products and should more than rival the same music on vinyl. However, just as with vinyl, you need to take care of the media and the machine.

Most of the tape available on ebay was produced when 7 1/2 & 3 3/4 ips and four tracks on 1/4 inch were an accepted media. You might be lucky enough to find an exception but the quest might not be worth the trouble.
There are those out there who own master tapes, or more likely copies, that will sell a dub, but you buy them without hearing them and the cost is higher per reel, than TTP. In most cases the sound is still better than the vinyl recording but you take your chances.

Regarding the operating position of the A810. I own a pair of A810s and originally ran them on their back. They ran extremely hot. One got so hot that the pinch roller softened enough to stick to the tape as it passed the capstan. It doubled around the pinch roller and ate about 15 inches of my TTP issue 2 tape. Fortunately, it was at a spot where a loss of one second of music wasn't noticeable. At the time I was making a safety copy of that tape! As it turned out, both machines had the original pinch rollers. Studer outsourced some of the rollers and determined that the material their supplier used wasn't cured properly. I purchased new rollers for both machines to eliminate the problem from reoccurring. I also stopped running the machines in a horizontal position. Stand them up and they'll run cooler. You can also get better cooling by loosening the two screws at the bottom left and right corners of the pres. This will enable you to swing the bottom of the electronics out which makes it easier to operate and let a bit more air in at the bottom of the machine. This feature was designed into the machine to make it easier to operate in tight conditions.

You also need to demagnetize and clean the tape heads every 8 hours or so depending on the speed you run the machine. Not doing so will result in a loss of highs you may attribute to poor tape or machine performance.

You'll need to grow into the do's and don't of RTR machines and tape media just the same as you did while wringing every bit of sound out of your vinyl.



good luck, Ken

Mitch4t-actually, a 'work-around' is available, as outlined in a post above: store the tapes 'tails-out', and when you want to play the tape, fast rewind, play, and again, store tails-out. Yes, you *do* need to listen to the entire tape, but you don't need to wait for a normal-speed rewind. I use a consistent theme of different colored leader tape for tips and tails, so I know at a glance how the tape is being stored, whether it be 4 track or 2 track.