Milty Zerostat - Questions


I recently purchased a new Milty Zerostat gun, but I don't think it's working properly. I need help answering the following:
- Am I using the Zerostat correctly?
- Do I have a defective unit?
- Is this yet more audiophile BS?

Usage:
I hold the gun about 5" above the spinning record, slowly pulling the trigger (no click). I then point the gun elsewhere when releasing the trigger, and repeat this about 2 or 3 times per side. I can hear a very, very faint burst of air emitted from the gun, but it doesn't sound like very much.

Problem:
I have a box of recently inherited albums, all of which are in good condition, but have a substantial amount of static cling (and dust). After using the Zerostat in the method described above, I have failed to notice any audible difference. There is still a noticeable amount of pops/crackles when I play the records. Additionally, I have found that the dust particles (or paper particles from the inserts) have not loosened either. The record brush just spreads the crap around, so to speak. These records probably need a good cleaning, but shouldn't the Zerostat help... at least a bit?

Testing the Unit:
Included in the packaging is a small 'plastic bit' that you affix to the nozzle. When you pull the trigger, the light bulb inside the plastic bit should glow slightly, if the gun is in proper working order. When I attempt this test, the light bulb glows very, very faintly, if at all, and only for a short period of time (.5 seconds). The light bulb definitely glows when I pull the trigger quickly and hear a click. So, do I have a defective unit? The instructions on the box made it sound as if the test is hit or miss.

Should I be kicking myself for spending $100 on a plastic gun? Any/all help would be greatly appreciated (sorry for the book).
jferreir
I don't feel I'm using the gun imporoperly by pointing it at the object when pulling and releasing the trigger. If the gun was designed to only release positive ions then why does it release negative ions when the trigger is relaxed? I agree with Tpreaves, if you don't feel it's worth the money get rid of it and move on. When I was dabbling with vinyl years ago I too bought new vinyl, wet cleaned it, used the zerostat and still had surface noise issues. I use it on CDs now as I have left vinyl alone for the time being, my discs sound better after using the zerostat.
I was simply pointing out that the method you described runs counter to the printed instructions for the Milty Zerostat. Perhaps it's different for the older model, I do not know.

As I've already said, I'm not here to complain about the purchase. I'm here to understand why this product is so popular. Believe me, I'm not losing any sleep over this. I'm just genuinely curious why so many people are adamant about its effectiveness, when it is unclear how it should be operated in the first place. Since I didn't notice any improvement, I would like to know how others measure the result. From what others have written, it appears that the Zerostat is most effective when used in conjunction with a RCM, but pretty impotent otherwise.
I am using the Zerostat by Dishwasher to rid my record of static. Period. To check for static hold your record tilted on the edge and drop a styrofoam packing peanut or bits of a crumpled styrofoam cup. If the bits cling, you have static which attracts dust while sitting on your platter. If your Zerostat is working properly, the styrofoam should just glide right off. No more static. That's all this unit does and nothing more. All the noise you complain about sounds like dirty records and should be cleaned as other people have suggested. Regretably, even brand new records are not guarateed to be noise free. This is why I don't bother going out of my way to buy them and prefer the original pressings (and clean them before I play them). Also, the Zerostat, it's claimed, helps CD's. I zap my CD's before I play them when I can. I've been too lazy to A-B the sounds of Zerostated CD versus un-Zerostated but I'm not losing too much sleep over it. In short, I use my Zerostat to rid static on cleaned records to repel dust that might fall on the surface while they are merrily spinning away. Good luck.
I am using the Zerostat by Dishwasher to rid my record of static. Period.... That's all this unit does and nothing more.
I agree. What it does is to eliminate static which in turn would attract dust while the record is exposed.

The instructions with my Milty, btw, say to hold it 12 inches above the record, not the smaller distances which have been mentioned.

Those instructions do not address the question of whether or not the gun should be pointed at the record as the trigger is released. However, I recall that the instructions for the Diskwasher Zerostat that I used to have recommended three successive squeezes and releases, with the gun pointed away from the record only during the last of the three releases.

That procedure seems to make sense, as it would reduce the likelihood of either a positive or negative charge being left on the record, compared to a single squeeze or a single squeeze/release.

I choose to repeat those three cycles at each of three different points around the record, from a little closer than the 12 inches that is recommended in the version of the instructions that I have.

Regards,
-- Al

Jferreir, your assertion of how the gun should be used is very accurate in my book. However, what you describe with the trigger and the faint bulb light indicates a broken gun. Mine broke the same way last week after a year's light use and have ordered a new one. It has been well known to me that the zerostat's build quality isn't what it was - see also http://www.2spi.com/catalog/photo/zerostat.shtml

"Because of quality problems in the manufacture of the Zerostat 3, SPI Supplies has suspended sales of this product until further notice."