2. analog
  3. 1292677307

Triplanar is compatible with a Peripheral Clamp

I have just modified my newly mounted Triplanar VII UII so that it plays LPs coupled to the platter with my peripheral ring clamp in position.

I have a Clearaudio Master Reference with its dedicated Outer Ring (i.e. peripheral ring clamp).

Initial Problem: the Triplanar was ‘catching’ on the latter side of the Outer Ring when the cartridge was reading the lead-out grooves (i.e the silent grooves at the end of an LP).

Solution: The modification consisted of ‘filing off’ 2mm of the plastic black cap on the front of the lower tonearm tube.

Materials used: Riffler File (flat parallel filing area; rough); Needle File (flat parallel, No2 cut); Wet and Dry Sand paper (P600); Toothpaste; Ear Cotton Buds; decorators polystyrene sheet; acid free tape

Method: Modification done with the tonearm mounted on the turntable (i.e: no need to remove the tonearm for the modification). Tonearm secured in the armrest that (the armrest) was immobilised in position with one loop of acid free tape. With the exception of the black cap, the rest of the tonearm and turntable were covered with polystyrene sheet, secured in place with acid free tape.
Three consecutive stages of filing (Riffler then Needle then Sandpaper) followed by polishing with toothpaste on cotton bud resulted in a finish indistinguishable from the non-filed part of the black cap.

Time for the modification: 2 hours, mostly on securing the tonearm and the polystyrene sheet.

Limitations of modification: VTA range is *limited* to 10 full clockwise revolutions from the horizontal. With 11 full revolutions the underside of the upper tonearm tube catches the upper side of my peripheral clamp.

Acknowledgements: The modification above would not have happened save for the help of following three people:

Tri Mai confirmed to me that the black cap is solid allowing me to start filing without the fear that I will end up with an unsightly hole in front of the lower tonearm tube.

Atmasphere provided me with a new L-bracket when the screw in the old one got stuck.

DougDeacon provided me with a list of possible solutions to the problem of operating a Triplanar with a peripheral clamp; in that list the absence of any documented Triplanar tweaking solving the problem allowed me to brainstorm the above modification.

Any criticisms or contributions to refining the above tweak will be greatly appreciated.

Many thanks in advance
kostas_1
dougdeacon
3,338 posts
 
You are indeed a brave man!

In addition to your sensible question to Tri Mai about the construction of the cap, I'd have been wondered about potential damage or dis-adjustment of the bearings from the pressures of filing, especially with the Riffler.

The ring I had (not a Clearaudio) was so wide that this method would not have helped, but I'm glad it did for you!

Cheers,
Doug
lewm
13,340 posts
 
Glad you worked it out. It is unfortunate that one of the innovative features of the Triplanar (the tower to adjust VTA) which required that the bearing and tonearm assembly are offset to the right, is therefore also the cause of problems in mounting the tonearm on certain turntables, let alone problems in relation to using peripheral ring weights. For example, it is darned near impossible to mount a Triplanar on an SP10 Mk2 or Mk3, because the square escutcheon that demarcates the turntable chassis will not allow the Triplanar mount to get close enough to permit proper pivot to stylus distance, without also seriously skewing the mount clockwise, so that the tonearm would have to hang over the LP surface when at rest. (Obviously, I've tried.) I wonder whether this has been a problem with two other tonearms that in this structural way pay homage to the Triplanar. I refer to the Reed and the Talea. Anyone?
thom_at_galibier_design's avatar
thom_at_galibier_design
729 posts
 
Hi Lew,

For every question about the Tri-Planar's choice of offset direction, there's an owner of a turntable which is limited to mounting the range of typical 9" tonearms.

With an effective length of 250mm (remember that 254mm = 10 in.) the offset pattern of the Tri-Planar yields a mounting center distance of about 213mm or approximately that of an SME and Linn 9" arm ("short" 9-inchers).

Choosing to offset to the opposite side would make the Tri-Planar mount like an arm that's longer than its 250mm mounting distance - not a smart move, IMHO.

In designing the Stelvio-II's tonearm mounting area, I wrestled long and hard - plotting the "landing pattern" of quite a few tonearms - then, deciding which ones to eliminate (if any) - to keep the base from becoming too unmanageable. Ultimately, I sacrificed the 12-inchers into custom territory - ones that could still be mounted but required an over-sized armboard.

As far as peripheral clamps are concerned, I've used them (and loved them) on a Merrill Heriloom. At the same time, this was plainly too much ritual to play an LP.

One of the outcomes of my platter designs was to maximize energy drainage from the LP without the need or resorting to any form of clamping.

I appreciate the benefits of clamping (both center as well as peripheral) to some designs. At the same time, the risks to cantilever damage (from periphery clamps) is VERY REAL, and something I encourage my customers to try at a risk to both their cartridges and their patience.

Cheers,
Thom @ Galibier

Cheers,
Thom
thom_at_galibier_design's avatar
thom_at_galibier_design
729 posts
 
oh ... and to the original poster. Nice work. I appreciate your passion.

Cheers,
Thom @ Galibier
lewm
13,340 posts
 
Hi Thom,
I agree with your assessment of ring weights. In fact, on balance I could live without record weights, record clamps, AND peripheral ring weights. (I now never use either of the former, occasionally use the ring.) Not only do they add to the necessary ritual of playing an LP, in my system they also can rob the music of some sense of liveliness that I delight in. I guess there is a point where excessive damping of resonance is not such a good thing.
More to discover