Is there a list of cartridge capacitance?


My phono stage has various cap values, but I can't see the cap value of my cartridge(Clearaudio Talisman V2 Gold)anywhere in the literature from Clearaudio.

I do have the cap value for my tonearm cables,28pf/ft.

Has anyone found a list of cartridge capacitance that I can use to properly set the values on my phono stage?

Please,I've done enough experimenting, and the answer is there are numerous settings that "sound good", I would just like to confirm if what sounds good to my ears jives with what is prescribed to sound the best vis a vis the correct match up of capicitance between cartridge and tone arm wires.

lacee
MC carts are affected by capacitance. Its just that the values are generally much greater than those that affect MI or MM carts, due to their much lower source impedances. It will affect HO MC more than LO MC.

On the vinyl engine site there is a calculator that can compute the impact of cable/preamp input capacitance on any cart, including MC, if you know the source resistance and inductance of the cartridge. Look under "database tools":

http://www.vinylengine.com/cartridge_database_tools.php

Then down to "Cartridge/Amp Loading/Resonance"

Input the resistance and inductance for your cart, and input capacitance values to see what the resonant frequency is. I think anything above 20 KHz is fine, so capacitance values up to that resonant frequency should be OK.
Dear Dhl93449: Yes, of course are affected but in our each one system in normal MC set ups has no " effect " so why speaks of something that is useless for whom is asking? why create more " confusion " on people that are not an expert on the subject as you are.?

Now, please share with us any first hand experience with a LOMC ( the Talisman on thread subject is a LOMC not a HOMC. ) cartridge where you change capacitance with a change in the quality performance level of that cartridge. I tried several times changes on capacitance values with several LOMC cartridges with out " effect ". Of course inside the capacitance values that normaly permits any phono stage.

Regards and enjoy the music,
R.
See the post by cartridge designer Jonathan Carr dated 8-14-10 in this thread for an explanation of the relevance of load capacitance to LOMC's.

Also see the discussion in this thread, particularly the comments by Atmasphere.

In general, with LOMC's the lower the load capacitance the better. Although whatever difference it may make will be dependent on the particular phono stage that is being used, and in some cases there may be no difference.

Regards,
-- Al
I've found that 100 ohms sounds better to my ears than the 400 ohms Clearaudio states.

Also ,30 /pf cap seems to work using the 55 gain setting.

I came upon a review of a review of another Clearaudio cart, the insider and for me this works.

I use Nordost 2 Frey as tonearm wire from my SME V arm and my IC from Steelhead to power amps is Heimdal series 1(why did they not include the WBT next gen on the Norse 2 series ?).

So cable cap may not be as big an issue for me using these cables,but it never hurts to try to get the max performance out of what we have.

Messing about with the cap seetings did change the sound when I was using the Grado Plat and the Rega Exact 2 on my P9 table.

It's been awhile since I was in the MC camp,my first times were with a Fidelity Research FR1mk3f and a Cotter P strapping transformer.I remember how important it was that the transformer be a correct match.

I flit back and forth between 400 ohms and 100 ohms and it seems to add or subtract depending on the LP.

Thanks for all the great advice and references,dialing in a cartridge isn't rocket science, but sometimes it's nice to know if what you settle for is within the accepted wisdom and not out in right field.

What matters is how it sounds after all the fiddling is over with.
Dear Almarg: Thank's to bring those links that I'm aware of.

A>s I posted, I made and have experiences changing capacitance with LOMC cartridges and I can't remember changes on quality level performance. I'm not saying that capacitance can't affect about but if you can't detect it all the theory could be only theory.
Of course that maybe my system has not enough resolution or my ears could be not good enough to distinguish that capacitance subject. Maybe you can do it but I don't know: could you share your experiernces about?, thank you in advance.

Regards and enjoy the music,
R.