best rca cable for deep controlled bass

It puts out a solid 100 wpc into 8 ohms and 175 into 4 ohms, both channels driven. It's able to deliver a lot of current when called for, and the amp sounds bigger than its power rating would suggest.

The amp in question is the Onkyo A-9555 hybrid switching integrated amplifier, rated at around 85 wpc into 8 ohms. Double that output into 4 ohms and sum the output of both channels to come up with Hifihvn's

Johnnyb53, you try to make an impression that you have a high level of knowledge like an Electrical Engineer. Anyone with some basic electronics education would know that you can't get something for nothing. This would be like a "Perpetual Motion Machine". The amp would save the worlds energy problems, if it worked like you must think it does. In the audio world, a stereo amp should be rated with both channels driven at the *same* time. This is why the IHF worked with the government years back, to get rid of phony "peak power" ratings. But no, these companies found loop holes in the law, and use them. The real companies use the true ratings, especially the high end American companies. This Onkyo consumes 110 watts max. That includes all loss do to thermal, and other issues in the design. *If* it ran at 100% percent efficiency (doesn't work that way) , that would give 55 watts RMS per channel. That 175 watt per channel quote, is from *your* figures, in *your* prior statement, not mine. If you want to be an Electrical Engineer, see if you could go to a University, and become one. You will have to do a lot of learning, and just can't throw some figures around there. That sure will not happen. Try to be more informed, and accurate. Link for your statement first, and link for Onkyo that has
specs that show it only consumes 110 watts.[http://forum.audiogon.com/cgi-bin/fr.pl?aamps&1170999828&openusid&zzJohnnyb53&4&5][http://www.onkyousa.com/model.cfm?m=A-9555&class=Amplifier&p=s]

If a 3rd party test (Stereophile) measures 175 wpc into 4 ohms, I would believe those results before drawing some sweeping conclusion based on the manufacturer's spec sheet, which may even be a misprint.

Your assertion about power consumption vs. power output motivated me to search out the specs on some new ultra-light class D bass guitar amplifiers. Gallien-Krueger, a specialist in this area, has an amp that makes 200w into 4 ohms and draws 240 watts max. They have another amp that makes 500w into 4 ohms and consumes 580 watts at full power. So class D switching amps (which the Onkyo is) are very efficient. Since the Onkyo specs DO NOT specify 110 watts as the MAX draw, I can only conclude that it either means typical or average consumption or it is erroneous. I sure wouldn't base the capabilities of the amp on one unqualified mfr's spec, especially when a 3rd party (Stereophile) independently verified that the Onkyo produced 110 wpc (both channels driven) into 8 ohms and 175 wpc (again, both channels driven) into 4 ohms.

I have one last question, however. What does any of this have to do with finding interconnects with good bass response?

Sure, a lot of equipment could put out more that it's designed for, but this is short term only. Audiophiles want their amps to give the real power(true watts RMS), both channels driven,20 to 20,000 hz, on a continuous basis. Now that these companies have found ways to use figures such as at 1khz, or whatever else they can to give you a phony rating. Here is an Onkyo receiver that can make one think it will give 135 watts a channel. But the test results show it is far from it. And they only tested it at 1khz, not at 20 to 20,000 hz. Sure an easy test, but failed. Links for this Onkyo.[http://www.us.onkyo.com/model.cfm?m=TX-NR1008&class=Receiver&p=f][http://www.soundandvisionmag.com/content/onkyo-tx-nr1008-av-receiver]

In reference to your second question, one would assume you know the basics, before getting into high tech talk.

READ THE STEREOPHILE REPORT! They tested it according to FTC requirements--one hour 1/3-power burn-in, testing from 20-20KHz continuous power output both channels driven. It measured 110 wpc into 8 ohms and 175 wpc into 4 ohms. What part of that don't you understand? Who cares what the Onkyo specs say when a 3rd party put it on the test bench and tested strictly according to the FTC rules?

In reference to my second question, it's not an issue of "tech talk," it's basic forum courtesy to stick to the OP's subject and not hijack his thread about interconnects by bringing in a 3-year-old post about an amplifier.

Defining clipping as 1% THD, the A-9555 comfortably exceeded its rated power, clipping at 110Wpc into 8 ohms (20.4dBW), 175Wpc into 4 ohms (19.4dBW), and, with one channel driven rather than two, 245W into 2 ohms (17.9dBW) (footnote 1). There is a peculiar rise in the A-9555's THD+N percentage when the output reaches a few watts;

I can read. They pre-conditioned it at one third its rated power. Its rated power is at 1khz, not 20-20,000 hz hz. I only read that they tested it at the way they rated it, for
1 khz. Onkyo themselves say 85 watts at 1khz. Major difference. Don't understand? Apparently not. That's the problem. FWIW, that *at 1 khz* is one of the loopholes. Who listens to 1 khz only? And clipping? You I guess. Onkyo 1khz specs. LOL.
[http://www.stereophile.com/content/onkyo-9555-integrated-amplifier-specifications]