Directional speaker cables - switching direction


Some time ago I started a thread regarding speaker wire directionality and my inability to understand how it could have any affect on sound quality. The question was inspired by the fact that, after quite a few years using them with my Martin Logan Odysseys, I discovered that the cables (Straightwire Octave 2) had arrows printed on them. Not surprisingly the opinions expressed were pretty strong on both sides of the argument but those supporting directionality were the most vociferous and in greater numbers, one to the point of being downright insulting. In no case, though, was an explanation given by those supporting the importance of cable direction for how this phenomenon occurs except that it should be obvious that when a cable is broken in in one direction only someone with an uneducated ear would be unable to discern the difference.

Even though I still don't get it I'm not taking the position that there is no validity to the directional claim; if there truly is I just don't understand how. This leads me to my two part question. I haven't been using the Octaves for a few years but now, because of cable length issues, I want to put them back in my system partly to avoid the cost of new quality cables.

IF, then, the directionality theory IS valid and I don't recall which way the arrows originally pointed or which direction they were "broken in" do those in support of directionality think I should install them with the arrows pointing toward the speakers
128x128broadstone
Here is the Link for the Sterophile/transport Delight article I quoted earlier.
.
For some strange reason when I paste the link between the [url ]....[/url] brackets the web site is not displayed.
Mike, thanks for your comment.

Getting back to speaker cables, it occurs to me that what I said about connector-related impedance discontinuities in relation to digital cables may have some applicability to speaker cables as well. Speaker cables will to some degree act as antennas, picking up Radio Frequency Interference from various sources, such as nearby cables, power cords, digital components, switching power supplies, light dimmers, fluorescent lights, possibly wifi and even radio stations. That RFI will presumably be at frequencies that are too high, and at amplitudes that are too low, for the speakers to reproduce it and for our ears to hear it. However if the amplifier uses feedback, and if (as I would expect to often be the case) the amplifier's output impedance at RF frequencies is significant, some of that RF energy will be introduced into the feedback loop. Non-linearities and intermodulation effects within the amp may then result in that energy affecting sonics at audible frequencies.

And the magnitude and frequency characteristics of the RFI that is injected into the feedback loop can be expected to vary to some degree depending on the differing impedance discontinuities and mismatches at the two ends of the cable.

The magnitude and frequency characteristics of the RFI that is injected into the feedback loop might even differ significantly depending on the exact physical placement of the spade lug or other termination on the binding post, and/or its positioning relative to nearby metallic surfaces on the amp. As I said early in this thread, when hard to explain and/or seemingly implausible phenomena are being addressed, multiple back and forth comparisons are called for, to be sure that the observation is being attributed to the right variable, as well as to verify that perceived differences are perceived consistently.

Best regards,
-- Al
Jea48, not sure why you asked the last question, the one about flipping solid core silver, since silver or any metal solid or stranded conductor should exhibit directionality since they are crystal structures. Which brings me to this rather disturbing situation: if copper and silver cables are directional, then aren't all wires Nd fuses directional as well? If that last statement is TRUE then we have a big problem. Mathematically, unless someone tracked the wire as it came off the spool as Crump suggests, there is a 50% probability that any wire or conductor or fuse in the system is installed backwards. This holds TRUE for any internal wiring, capacitor, resistor, crossover network, speaker wiring, transformer, inductor or fuse. If you see what I mean.
By the way, there is probably no doubt about wire directionality being produced by the final die since cable manufacturers have been marking the wire as it comes off the spool for decades in order to be able to correctly mark the cables with ARROWS. Think of it like porcupine quills. Wouldn't it be easier to stroke a porcupine's back going in the direction of the quills instead of the opposite direction?