Please help with subwoofer.

I generally recommend 2 subs over 1. They are much easier to place and get a flat frequency response. For HT placing them mid way across a wall and the other on the opposite side of the room will give you the flattest frequency response. In addition to this I think the F series subwoofer sounds better than the HGS (I know many will disagree with me here, but the HGS sounds like a motor to me). If you go to our website, www.rivesaudio.com, and enter the listening room (it's throug acoustical issues), there is a button for speakers. Go to that page and there's a link that will give our methods for speaker placement, including subwoofers. We will be updating that paper in the upcoming weeks, but it's still very useful now.

If its only for movies then I would go with the two F-1800 set up. Thats a big area and you need to move a lot of air so I think you would do better with the two sub set up. One thing thats nice to try with two subs is to put one up front and one in the rear.Wire the rear sub out of phase with the front one, makes the bass roll threw like a wave. enjoy

Hello Mitch,
Let me add my 2 cents if I may. Intergrating a subwoofer has 2 major challeneges. (Audiogoners don't have problems, only challenges). One would be crossing the sub over to the mains, the other is that damn room resonate point that howels like a Kansas timber wolf when there is a full moon. Lets look at the cross over issue first. I've owned a FSR-18 velodyne and found it very flexible to intergrate. The FSR and HGS Velodyne's give you the option of shutting off the crossover in the sub and using the crossover in your HT processor. Usually the crossovers are superior in the HT processor than in the sub, so as Albert pointed out use the best crossover available. Also if you are using the sub out from HT processor and also have the crossover in the sub engauged, the two crossovers will bang off each other raising all kind of hell. If you eventually pick a sub that DOSE NOT allow you to turn off crossover then dial the cut off up as high as it will go, lets say to 100hz or 120hz. This will move the sub's crossover point futher away from the HT processors's crossover and cause less ringing from the two crossovers colliding. So in short use the HT processor's superior Xover (as suggested by Albert) and shut the Xover in the sub off. The Velodyne FSR and HSG series allow you to do this. I'm not sure if the Velodyne F series has this ability? For regular 2 channel intergration I ask use to search Audiogon member Danner's post on 11-20-02 about picking a crossover point relative to the subs -3bB. Next point howeling Kansas timber wolfs'( room resonate points). The size of your room will dictate the lowest possibe frequency that your system will produce. That would be the length (peak to peak) that will physically fit into the room. Possibly Mr Rives can expound on this, but in short my 16x27 HT room can go down to about 25hz. Your 22x70 room will probably go down into the single digites. Thats a good thing as Martha would say. Now when everybody gets excited and brags about their sub shaking and rattling the room, sorry wrong answer !!! You are only hitting the rooms resonate point. That not a good thing. The smaller the room the higher the resonate point. My friend Luc from Canada has a smallish room, I believe its about 12x20. His room starts to sing between 70 and 80hz. My 16x27 room seem to have a nasty howel around 45 to 50hz, your 22x70 room should have a much lower resonate point do to its size. Thats a good thing. I think many newcomers confuse the room resonate problem (muddy base) with the crossover problem. two seperate issuses. Room resonate problems can be aided by careful speaker placement and the addition of a second sub to help smooth out standing waves. The addition of a second sub will also increase the bass output by 3dB, again a good thing in you hugh room. If you are looking at a pair of F1800's your problably involved with that WILD MAN, audiogon member Porschcab. he seems to be having a blast putting together his HT. One burning question for Dan if you are on board, why o why did you sell that Theata Cassablanca 2 with extreme dac's??? One last point I think often overlooked. Don't buy a cheap cable to run to your sub . It will probably be the longest cable in your system and your biggest antenna for picking air born noise generated in your room. Spring for some thing with a good shield to reject as much RFI as possible. Also the Velodyne's have noisey switching power supplies, which will send noise back down the power cord and also balloning back into the room only to be pick up by other sensitive equipment. I've had excellent results when switching from the stock Velodyne power cord to the ESP's I use throughout my system. Hope this helps. I'm sure others will have some comments both pro and con to what I've said. Welcome to the jungle.
Good Luck
Dave

Ps: Am I the one who said we don't have problems only challeneges look how many times I used the word problem in my post. What a huckelberry I can be at times!

PPS: Albert congradulations on your Texans totally embarrasing my New York Giants yesterday.

Davehrab, I am not a follower of sports, so I was unaware of our Texans doing well against the Giants.

I am impressed with your comments above though, much to think about for the HT challenged. I keep mine simple and concentrate on stereo.

I TOO HAVE A PAIR OF 9 KAPPAS POWERED BY A PAIR OF SUNFIRE SIG. AMPS...ONE AMP PER SIDE...ROLLING OFF AT 60HZ TO A PAIR OF VELODYNE FSR18 SUBS...THE SHALLOW DEPTH OF THE KAPPAS REALLY LIMIT THEIR LOW-END EXTENSION, AND THEY WILL SOUND SO MUCH BETTER WITH THE "PAIR" OF 18" SUBS!..IT'S LIKE YOU'VE NEVER REALLY HEARD THEM BEFORE!...BY THE WAY..WHEN YOU GET TIRED OF RE-FOAMING THE SURROUNDS....FIND SOME BETA 12'S AND THROW THEM IN...BUTYL RUBBER IS THE ANSWER!