Cable lengths

I have posted this before but... Here is an interesting article on the subject. Click the link below.

Equal Length Speaker Cables - Are They Necessary?

Now I remember too, Bwihite about that article.
Moreover, It's almost impossible to find a HT system that uses equal speaker wire runs for mains, sub, center and surrounds(ABSURD!)

In a situation similar to yours, e-man, I hedged my bets by making the shorter wire about two-thirds the length of the longer one. That's quite a bit longer than I needed, but I didn't want to have the difference between the two be too large. (It also leaves me with a length that's not too short to sell, if I wanted to.) I loosely gathered the excess into a sort of figure-eight shaped bow. Someone smarter than me said this would be better than a coil-- maybe Bear can comment. I don't know if I've come out ahead in terms of sound quality or not, but over extended listening I have not noticed any imbalance or deleterious effect. If I chose to approach this like a hobbyist and experimented and investigated, I might or might not discover some subtle differences, but it's easy for me to leave this alone.

That inductance is measurable at audio frequencies.

If you look at the output of a typical solid state amplifier with an inductor in the output you can easily measure the change in the way a square wave is reproduced with and without the inductor when driving a capacitive load. Most speakers have a capacitive load angle somewhere.

So, it is highly probable that increasing the series inductance that the amp sees WILL have a measureable and probably audible effect within the "audio range."

Published tests have shown that this small series inductance found in cables will cause a small but measurable drop by 20kHz. This is different than the square wave effect I mentioned above, but does show a measured effect within the "audio range."

In general it is a good idea to minimize these effects in a system that you are trying to optimize. If you are not trying to put together such a system, it won't matter at all.

_-_-bear

I did a quick experiment to see what the effects of coiling up 8' of a 13' speaker wire up would be. I took a 13' speaker cable (12 gauge oxygen free copper) and measured the effective resistance over 20 Hz - 300 kHz. I then coiled up 8' of the cable which made the effective length of the cable to be 5'. The coil was about 4 loops in a 6" diameter. I then measured the effective resistance again. Each line of the data is in this format:

Frequency,
Resistance of straight wire (milli-ohms),
Resistance of wound wire (milli-ohms),
% increase of resistance:

20 36.38 36.65 0.74
30 36.72 36.92 0.54
40 36.7 36.93 0.62
50 36.72 36.99 0.73
80 36.79 37.23 1.18
100 36.87 37.43 1.50
120 36.94 37.64 1.86
150 37.06 37.96 2.37
200 37.72 38.5 2.03
250 37.45 39.03 4.05
300 37.63 39.55 4.85
400 37.92 40.48 6.32
500 38.2 41.34 7.60
600 38.46 42.17 8.80
800 38.95 43.7 10.87
1000 39.41 45.14 12.69
2000 41.06 51 19.49
4000 43.66 59.9 27.11
5000 44.84 63.77 29.68
6000 45.81 67.28 31.91
8000 47.66 73.9 35.51
10000 49.47 80.14 38.27
12000 51.32 86.16 40.44
15000 54 94.62 42.93
20000 58.36 107.76 45.84
25000 62.5 119.8 47.83
30000 66.55 131.05 49.22
40000 74.25 151.6 51.02
50000 81.9 171 52.11
60000 89 188 52.66
75000 99 213 53.52
100000 118 251 52.99
300000 255 505 49.50