Dynaudio Audience vs. Contour

Unfortunately, I have not specifically heard the 1.3mk2, since it has been discontinued. Hence the reason for the post. I have heard some of the other contours, and I like the better high end definition. However, I thought the tonal balance was better on the 52s... As I recall, the contour high bass seemed a little prominent.

I will be running the speakers off of a Rotel 1055 receiver (75w/ch conservative) which is a high current receiver. I think it is supposed to be a good match for either the Audience or Contours, but If you think otherwise, please let me know.

I also already have the T2.1 Contour center, which should blend fine for both. I am also using a REL Q100 sub.

I guess my big question is do YOU think the Contour 1.3 mk2 sounds better than the 52s...and do YOU think there is a problem with tonal balance on the 1.3s.

THANKS.

Dan

Dan - I would much prefer the 1.3 mk2's taken as an issue by itself. That said, I think you'll find the 52's a better match for the Rotel. That's a nice receiver, but the discontinued Contour's (such as the 1.3's) REALLY soak up the current. Unless you're planning on upgrading the receiver in the fairly near future, I think you'll like the 52's better.

I do like the sound of the 1.3's better than the 52's and, no, I don't think there is a tonal balance problem. -Kirk

Thanks for your opinion on the 1.3mk2 Kirk. I look forward to hearing more opinions on them. I hope they really are a step up from the 52s, which I like a lot. By the way, have you heard the new Contour lineup? Are they really much improved, as advertised?

As far as the amp goes, I think the Rotel 1055 is supposed to be able to handle the contour 1.3mk2... they were paired together at the local HiFi store, and sounded very nice. The 75w/ch Rotel is a conservative rating, outguning other receivers (Sony, Denon, Onkyo, Marantz) rated over 125W/Ch. Reviews have mentioned that the unit performs similarly to separates, which has been their selling point. If anyone else has specific experience on the matter, I would love to hear it!

Thanks.

Dan

Dan, I have heard Dynaudio speaker with lesser electronics before and they just don't sound as good as they should. The issue is especially true if you plan on using a surround receiver. When all five speakers are going, there just isn't enough clean power being deliver to the main speakers.

Croos over to a high quality powered sub at 50-60Hz will solve the amp power issue, but you will also need a good digital processor with very clean bass management.

So the best way to go would be to have a good CD/DVD transport sending a digital signal to the surround processor and have the surround processor to adjust the cross over. Some of the newer surround pre/pros have variable digital bass management that can even solve bass loading problem. Check out B&K Ref50 or Anthem AVM20 or the newer Rotel pre/pro. I think the Rotel receiver can only do a fixed cross over at 80Hz and it might not be done in the digital domain.

The other option is go with a dedicated amp and just use the receiver as a preamp. You can pick up an used McCormack DNA or Aragon 4004/8008 for $1k. You can get have the cake and eat it too.

Thanks Ejliu-
I will be using a powered sub... the Rel Q100.
The Rotel 1055 is supposed to have an excellent digital processor. I am also using a good transport... the Sony 9000ES. As far as digital bass management, I'm not sure. If anyone has further advice, please post it.
The 1055 does have pre outs (in fact you have to use a separate poweramp for 6.1 or 7.1) that I could use if need be (I have an old NAD 3300 amp I guess I could fire up). I'm just not sure which speakers would use it.

Thanks.

Dan