Speaker priority: high or low???


I have been reading the threads here for some time and following many of the discussions. During an interchange with another well known AudiogoNer we were commenting on peoples tastes and priorities. The discussion turned to speakers and he made the comment "many people on AudiogoN still think that speakers are the most important piece of the system." I was floored by his statement.
I'm not trying to start a fight with anyone and people can see what I have previously posted about this and other subjects, BUT are there still a lot of people that share this opinion?
Do you think the most important componant is your speakers? If not, what do you consider to be the most important? Why do you place so much emphasis on this componant?
128x128nrchy
Just a note, Paul: It is not tube amplifiers that do not have flat response within the audioband - most do, as do amps in general. It is some speakers possessing uneven or reactive electrical impedance characteristics that will display slight deviations from flat response when driven by tube amplifiers, or by some SS amplifiers that eschew high levels of loop negative feedback in their designs.
I believe the room, speakers, amps, etc. direction of priorities is the way to go. I feel that the room and speakers need to work as one. In as much as you may like the sound of a speaker at a dealers, they may sound awful in another room. It's almost an electro-mechanical interaction. Speakers need the right amplification to perform properly. Personally I think speakers should be sold with outboard crossovers preceding appropriate amplification.I also find that speakers tend have the greatest variation in sound. This indicates to me that speakers are perhaps the most colored component in the chain. It's important that you find speakers with colorizations that offend you the least. I always find it interesting when I see post's asking for help choosing speakers around a particular amp. To me that would be like choosing an automobile to use with a particular gasoline. Now if you only had leaded low test available, that might make sense. I doubt that many have such an issue. Another cliche' we often see is "garbage in, garbage out". As far as I'm concerned, if you contaminate the system chain at any point you'll have garbage out. Just my humble opinion, to each his or her their own. We all find our own path to happiness.
I too am going to weigh in on the speaker end, with the provisos that (1) you do have to reach a certain level of amplifier and source performance, which varies from one individual to the next depending on what you can tolerate, and (2) really disparate levels of spending on source/amplification/speakers are bound to lead to a worse result than an intelligent distribution.

Having said that, there is absolutely no question that speakers have by far the biggest deviations and distortions from perfection, that is, they color the original signal far more than any other component, usually by several orders of magnitude! And the worst types of offenses are just "passed over" by the reviewers, e.g., a total lack of time or phase coherence, massive impedance and phase anomalies which put tremendous demands on the amplifier, highly inconsistent diffraction and dispersion patterns, etc. It's as if the reviewers take the attitude that "everyone does it, so it must be okay"! It's not even close to okay, it's just that very few speaker designers have tried to seriously address these issues.

I will make an even bolder statement: If you assembled a system of decent components including a typical 3-way rectangular-box speaker with a typical high-order multiway crossover, and then took a short sample of a complex musical signal and studied it all the way through the chain, it would remain largely intact until it reached the speakers, at which point it would instantly transform into a waveform that is literally nearly unrecognizable compared to the original. Of course, I could be proved wrong, but I doubt it. If anyone has done this, I would love to see a reference to it.

Please do not accuse me of suggesting that measurements are all that matter. I am merely suggesting that screwing up the waveform to such a degree that it hardly bears any resemblance to the original, cannot possibly be a good thing. There is a reason that full-range electrostatics sound so good, and it is that they avoid most of the problems I just mentioned. Of course, they have a whole new set of problems, most of which revolve around unsolvable room interactions, which is why most people don't put up with them.

So while I'm not saying that one should spend more money on speakers than anything else, I am saying that they have the most variability and thus deserve the most effort in searching for one that satisfies.
No system can ever sound better than the limitations of the "upstream" components. Since speakers are at the very end of the chain, though they may serve as tone controls, they can NEVER improve the signal passed to them.
Yes, David, you are right. The speaker cannot "improve" the signal presented to it. As I understand it, what Karls, Unsound and others have said (more ably than I) is that the speaker is the component that is least linear and most apt to impart its "sonic signature." There are clearly demonstrable, relatively gross (objectively and subjectively) differences between speakers. There are not such gross, subjectively and objectively demonstrable differences, for example, between a $500 CD player and a $2,000 CD player. A pair of AR3s is going to sound like a pair of AR3s with $20,000 worth of electronics and will sound like a pair of AR3s with $1,000 worth of electronics. --- The identifiable "quadness" of a pair of ELS 57s will remain regardless of the electronics. A bad amp may muddy the midbass, and present unacceptable colorations to the revealing midrange of the quad. And to be a bit hyperbolic: a deaf man would not mistake the AR3s for the Quads regardless of the electronics used with either or both.