Tube Amp for Martin Logan Speakers

Just a little background on my experience with the Manley Snappers.

I really think what can make a difference is how hard you're pushing the Snappers.

I was very concerned about the Snappers - given the specs - which is why I insisted on auditioning them before purchasing them. I had read that they were a tad more sweet in the midrange than the Rogue Audio M-150s (which is what I was planning on after reading some very positive reviews), but I suspected they wouldn't have the power to drive my Aeon i's - especially in the higher frequencies where the Aeon i's can drop down to just under 2 Ohms. And I should tell you that I am also using a pair of subs to augment the Aeon i's since they are totally passive and can only get down to 43Hz. But a practically brand new pair of Snappers came in at my local dealer's shop and he called me up and asked me if I wanted to try them out for a week. I decided to give them a try after speaking with Paul over at Manley Labs - being cognizant of the fact that my listening room is quite small and I would not likely be pushing the Snappers too hard.

All I can say is they sounded amazing through the Aeon i's. I brought over two audiophile friends - call them P and W. P is in his late 20's and can easily hear frequencies above 15kHz (which is actually pretty rare) and both were blown away by the sound. We we're comparing the Snappers with my Parasound HCA-3500 which has ZERO problem driving my ML's and the Snappers outperformed the 3500 in practically every way - especially on musicality and sound stage depth. What really shocked me was when W said he thought the Snappers had more slam than the 3500 - especially since slam is what the 3500 is really known for. P indicated that the highs were a bit more subdued with the Snappers, but they sounded much more pleasant in his mind. For W, there was no comparison - the Snappers sounded MUCH better in his mind - even to the point that he has now decided to move over to tubes. And we listened to all types of music - classical (full orchestra and smaller ensemble works), jazz (traditional and modern) and classic rock. Female vocals sounded especially life-like through the Snappers.

But keep in mind, the caveat to all this is the levels we were using for the audition given my room size. If you have a large room that needs some serious volume, then all the data does suggest that the Snappers will probably run out of steam and you might be better off with something like the M-150s or M-180's. But in my room at least, the Snappers had plenty of power to drive my Aeon i's with a level of quality that was leaps and bounds above the 3500.

Would a pair of M-150's or M-180's do better? Or one of the top-end Pass amps? Maybe. But all I can say is the Snappers were available, they were less than 8 months old and in like-new condition and they were priced at $3600 for the pair (they now retail new for $7200). So in my case at least, getting them was a no-brainer.

Specs are certainly important but they are not the end-all-be-all. At the end of the day, you really need to listen and decide for yourself how a component integrates with your existing system and room topology. For me, the Snappers were a major step-up and I'm totally happy with them.

Jan, please re-read my non-tech take 2 or 3 posts north of this post. What you describe is exactly the effect of using NF -- the amp compensates for the output voltage drop based on the amount of NF applied to increase the output voltage to compensate for the interaction of the amp's internal impedance load and the external load of the speakers.

The effect is more precisely described as the amp is behaving as though it has low output impedance. So ... the NF circuit does not really change the amp's internal impedance. Instead, it acts like a servo to cause the amp to compensate for the Ohm's Law effects.

Of course, as Al, Ralph and others have said, the amp can only do this if it operating within its power delivery limits -- i.e., SOA (safe operating area). Also, there are rarely any free rides. Hence, NF has its own problems, e.g., increased odd ordered harmonic distortion ... and its detractors, e.g., Ralph. IMO, amp designers make trade-offs in order to design and build amps that perform at a certain level at a certain price point.

Probably still not saying this correctly, but it goes to show how the terminology can get in the way even though we are all really saying the same thing.

Every once in a while I remember to use my memory :-).
One of the speakers used here was the earlier ML Aerius and not the OPs ML Aerius i, nevertheless it might be germane:

http://www.stereophile.com/reference/810/index.html

Byfwinne, yes I agree. The internal amp Zout is not changed of course.
Re: increased 3rd with nfb: that has been laid to rest many years ago. Most people know the (in)famous Baxandall graph showing increased harmonics (even harmonics that were not there without nfb) with increasing nfb. Then, when you continue to increase nfb, the harmonics eventually became invisible again - all of them.
There are two sides to this. One, not everybody realised that the worst you could do in this situation, was to use moderate nfb. For lowest harmonics, in this situation (see below), use none, or use a lot!
Second, this was a single, crummy FET stage. It has been shown that if you look at this with a whole amplifier rather than with a single crummy stage, the effect is not seen. If you start with a reasonable amplifier, applying nfb decreases ALL harmonics.

Bifwynne, if I may, not trying to split any hairs, but the term SOA has a very specific meaning for ss devices. The Safe Operating Area defines the combinations of current and voltage across the device, that it can withstand for a certain time before being destroyed. For instance, a power transistor might be rated for 100W dissipation, but that's not the full story. 10 amps at 10V, being 100W, would be OK indefinitely. BUT, 1 amp at 100V would NOT be OK indefinitely, although it is also 100W. That 1A/100V combination can only be withstood for, say, 100 milliseconds, and then it will let out all the magic smoke*.
Now over to amplifiers: they also have an area where they will operate as designed. As you noted, drive the level too high, they will clip. Drive too much level in too low a load and they may eventually overheat and break. One common accident on the test bench is full power at 20kHz - not many amps can hold out on that, and of course during music reproduction, they don't have to. But all this is not referred to as 'the SOA' of the amp.

* The reason is that at higher voltages, the current tends to hog a small part of the transistor die, so that small spot will heat up much more that the rest of the die. That small spot cannot handle the 100W the whole transistor could handle. It blows.