TT-101 turntables…or any DD decks

Hi Shane,
I won't be taking the Victor for repair unless something else happens....:-(
But if it does....I would take it to Chris Kymil.
He does all the amplifier and speaker repairs for Len Wallis and is very good.
I don't know if he can work on these complex turntables....but last time I was out there....I remember seeing a turntable or two sitting in his workroom.

Btw, do you think there are any problems with the table running for 3-4 days straight with the bearing etc?

This has yet to be tested on our old 'beauties'?......but I can't see anything intrinsically problematic about running them non-stop?
From my experiences so far.......the more and longer they are used....the better and more stable they appear to become?

I am hearing a noise from my TT101, but only at 45 rpm. It is silent at 33 rpm. It's an irregular regular pulsation that could be bearing friction, and in the absence of any other good ideas, I assume it IS bearing friction. I am planning to unscrew that plug at the bottom of the bearing well, to see what's going on, to clean up the bearing, and to re-lube. Has anyone had a similar problem or heard a similar noise? If anyone has done a re-lube, what did you use for lubricant? Any other issues re removing that plug? I know that someone mentioned it also controls platter height. This noise did not appear until after Bill Thalmann had run the tt for days on end, in order to prove to himself that the speed was stable after servicing it. The bearing is supposed to not need maintenance, but I have to think JVC Victor were not contemplating a 30+ year lifespan.

I doubt it's the bearing, Lew. I once heard a noise roughly of the kind you describe (it didn't sound like a pulsation, but I could hear it every 2nd or 3rd rotation). The noise was due to the platter scraping against the cover to the control panel. This had two different causes. First, the cover wasn't sufficiently screwed down tight enough. Second, after I messed with the bearing well, I evidently didn't reseat the platter to the same height (yes, the bearing screw at the bottom of the unit controls platter height). It sat too low and scraped against the control panel cover.

I relubed with Mobil 1 20w-50 motorcycle oil. There's no consensus on what to use, so I just used that almost at random. Prior to replacement, the existing bearing oil was quite dirty. Aigenga, another owner of the tt 101, did some experiments IIRC with different ball bearings, so you might pm him to get his insights prior to tackling it.

Since the bearing screw controls platter height, it is essential that you mark the screw's current position and count the number of rotations it takes to take it off. Some cement type compound was used to lock the screw in position. You'll need to deal with that and possibly consider a replacement after you're done. I didn't bother myself, but I know how exacting you are :).

Good luck. Am looking forward to hearing about how the Victor compares to the other direct drive giants that you own. I assume you have a giant plinth planned for it? Or are you, gasp, going to go nude?

Banquo, It is certainly true that the noise I hear is not "obviously" due to bearing friction, so I am open-minded as to other causes. But I did inspect the spacing around the platter, between the edge of the platter and the escutcheon, and I did not see any area of contact between the two. Is that what you mean?

As to the bearing, I gather you are saying that altho you do not think the noise is coming from the bearing you do think I should clean and lubricate the bearing. Yes?

I actually bought my TT101 as part of a QL10 ensemble. Thus I have the original Victor plinth with a 7045 tonearm mounted on it. My plan was, heaven forbid, to use it AS IS, first of all. After that, I was indeed thinking of a minimalist but heavy and sturdy probably metal support structure that I would say IS a plinth but some would say is a manifestation of plinthlessness. I am done with slate. I think it's great stuff, but I am finished with the aggravation associated with purchase, getting it cut, drilling holes, oiling the surface, etc, in order to end up with a nice finished product. I did it for SP10 Mk2, Mk3, and Denon DP80. Now I'm done.

But I did inspect the spacing around the platter, between the edge of the platter and the escutcheon, and I did not see any area of contact between the two.

Yeah, I didn't note any point of contact either, that's why it puzzled me for a couple of days. Perhaps I have mis-described the problem; can't be certain. Nevertheless, the 2 solutions I described for the noise I heard worked for me.

I assume no one messed with the bearing screw on yours. If my diagnosis is correct, then all you need to check is whether the escutcheon is screwed down tight. I mean really tight.

I believe the bearing oil is worth changing, if only for peace of mind. IIRC, Aigenga did it several times to try out different oils--so it's evidently not a difficult procedure. In other words, why not? Better now then after you have everything already set up.

I just remembered yet another cause for the noise I heard. I don't know if Bill had reason to unseat the motor, but in fact it rests on washers. If one forgets to put them back in, then the platter will be lower then it should be--and cause a noise every 2nd or 3d revolution. I recall now that I had to put those back because my second (sic!) tech forgot.