Try taking out your Silver i/cs and put in a Generic pair of Wallyworld specials ( plastic stuff ) ..and see if it might be the Silver being the culprit.....If so you may have tog oto another makeup of cable.........
Conrad Johnson PV11...Extreme sibilance, harsh sou
Hello everyone,
I have an issue and was wondering if I might prevail upon the community to help me out. I am a seasoned audiophile, I would like to think, but I am sure this old dog can still learn a few tricks.
I have recently acquired a CJ PV11 preamp that is basically in mint condition and came with a brand new tube set from CJ. The tubes were installed around 7/10 and I received this amp on 7/28/07. (strange though, they used Electro-Harmonics tubes)
Anyway, After I installed the preamp, I now have very serious issues with harsh mid range and extreme Sibilance issues that I never had before.
My system is very revealing. I use NEW Walsh drivers based on the Ohm Acoustics design of the model "F" and "A". In fact I have both. These units I make and build myself.
I have not even attempted to use the phono section of this preamp yet. Just the line stage.
While I have never encountered this problem before, I have it now, so much so that I can barely stand to listen to my system. Nothing in my system has changed except the preamp. I intend to rebalance the room and speakers using my calibrated mic and high quality RTA. And even though I am a purist at heart, I do use a high quality graphic equalizer just to cope with some room acoustic issues, but it is set to a very low and flat curve and mainly compensates for low end reflections from my omnidirectional speakers.
I have read about the usual tube rolling, try different interconnects and ac conditioning, but most of that seems very subjective, even to those that suggested it.
I do use dedicated 30 amp lines and separate grounds for my system and even have an ac conditioner, but found the conditioner caused hum issues, strange as that might seem. So I took it out and run direct to the line.
My speaker cables unfortunately are long runs of 25 feet by necessity, but are high quality OFHC braided cables with a 10 ga. size. I also use silver interconnects that I have designed.
Does anyone have any ideas? I have put into CJ for help, but no response yet. (Holiday) and have also been in contact with Dr. Tube.
I would appreciate any help.
Thanks in advance.
Dale
I have an issue and was wondering if I might prevail upon the community to help me out. I am a seasoned audiophile, I would like to think, but I am sure this old dog can still learn a few tricks.
I have recently acquired a CJ PV11 preamp that is basically in mint condition and came with a brand new tube set from CJ. The tubes were installed around 7/10 and I received this amp on 7/28/07. (strange though, they used Electro-Harmonics tubes)
Anyway, After I installed the preamp, I now have very serious issues with harsh mid range and extreme Sibilance issues that I never had before.
My system is very revealing. I use NEW Walsh drivers based on the Ohm Acoustics design of the model "F" and "A". In fact I have both. These units I make and build myself.
I have not even attempted to use the phono section of this preamp yet. Just the line stage.
While I have never encountered this problem before, I have it now, so much so that I can barely stand to listen to my system. Nothing in my system has changed except the preamp. I intend to rebalance the room and speakers using my calibrated mic and high quality RTA. And even though I am a purist at heart, I do use a high quality graphic equalizer just to cope with some room acoustic issues, but it is set to a very low and flat curve and mainly compensates for low end reflections from my omnidirectional speakers.
I have read about the usual tube rolling, try different interconnects and ac conditioning, but most of that seems very subjective, even to those that suggested it.
I do use dedicated 30 amp lines and separate grounds for my system and even have an ac conditioner, but found the conditioner caused hum issues, strange as that might seem. So I took it out and run direct to the line.
My speaker cables unfortunately are long runs of 25 feet by necessity, but are high quality OFHC braided cables with a 10 ga. size. I also use silver interconnects that I have designed.
Does anyone have any ideas? I have put into CJ for help, but no response yet. (Holiday) and have also been in contact with Dr. Tube.
I would appreciate any help.
Thanks in advance.
Dale
- ...
- 36 posts total
- 36 posts total