You are correct in assuming that the Arcam amps(same power) will be matched, and you don't need further attenuation. You have to realize that the crossover point of that system(601 Series 2) is at 4kHz, and very little music actually exists above that freq(that's why the difference seemed so huge with most everything below that gone). Bi-amping with a much lower crossover point(say with Snell 3 ways); the disparity would not seem as great. I would stay with the horizontal configuration, as there will be a pair of interconnects on one channel and not the other, if you go vertical. That may cause somewhat of an imbalance in your presentation.
Bi-amp befuddlement
Newbie in midst of modest upgrades to old system and wondering if I am getting best benefit from bi-amping:
Having read about it, I acquired an Arcam 8 power amp to pair with my Arcam 8 Integrated.
Speakers are B&W 601 S2, about 20 years old, which sounded quite warm and nice bi-wired with Monster cables. For the bi-amping effort, I bought Anti-cables.
I followed the Arcam instructions and wired the power amp to low end, the integrated to high end. Frankly, not sure I noticed a difference - except maybe when I crank it up. The sounds seems clearer, with less distortion, or maybe that's wishful hearing.
I am questioning things in part because the other day, I shut down the power amp and the music nstantly went tinny, like some tranmission from space. Put on the power amp, and all richness floods back. Clearly, I expect a change but not such a massive one.
Is that normal? Is that all I am getting out of the intergrated? I have looked at Audiogon forums and read about vertical bi-amping - one amp per speaker. Is that a better use of two amps for somebody who is not going to mess with speaker cross-overs?
Having read about it, I acquired an Arcam 8 power amp to pair with my Arcam 8 Integrated.
Speakers are B&W 601 S2, about 20 years old, which sounded quite warm and nice bi-wired with Monster cables. For the bi-amping effort, I bought Anti-cables.
I followed the Arcam instructions and wired the power amp to low end, the integrated to high end. Frankly, not sure I noticed a difference - except maybe when I crank it up. The sounds seems clearer, with less distortion, or maybe that's wishful hearing.
I am questioning things in part because the other day, I shut down the power amp and the music nstantly went tinny, like some tranmission from space. Put on the power amp, and all richness floods back. Clearly, I expect a change but not such a massive one.
Is that normal? Is that all I am getting out of the intergrated? I have looked at Audiogon forums and read about vertical bi-amping - one amp per speaker. Is that a better use of two amps for somebody who is not going to mess with speaker cross-overs?
- ...
- 11 posts total
Rodman makes excellent points, but on the question of horizontal vs. vertical biamping, there are arguments that can be made both ways. See the comments by the noted designer Steve McCormack, favoring vertical biamping, in this thread: http://forum.audiogon.com/cgi-bin/fr.pl?aamps&1234896660 Ultimately, of course, the tradeoffs will be system dependent, and the only way to judge what is best for your particular system is to try it both ways. Regards, -- Al |
I had not been biamping for some time , first because I was using my M3 and didn't have a good match for it and then because I was comparing my Spendor SP1/2s to the Mini Utopias which have only one terminal. A couple of days ago I decided to biamp the Spendors with 4 of my Meridian 605s. I had forgotten how much better biamping is, things stand out without straining to hear them and you hear things that were not there before. The Spendors cross quite high also but difference biamping is considerable. |
- 11 posts total