2. amps-preamps
  3. 1282688770

Using Receiver as a Switcher?

I currently have a Marantz SR7002 receiver powering my Vienna Acoustics Beethoven Concert Grands. When I was at Best Buy Magnolia I decided to stop by and see what their VA Mozarts sounded like by comparison. To my chagrin, they sounded better/clearer to my ears in the mids and highs. I'm not sure how much of this may be due to the room acoustics, but I noticed they had a Denon DRA-CX3 integrated amp powering the Mozarts.

I really have three questions. First, is the DRA-CX3 really THAT much better than the Marantz SR7002? My dad seems to be under the impression that as long as an amp has the power to drive the speakers without distortion (and it's not a tube amp), then there should be an extremely negligible difference in sound quality between amplifiers, and that what I have is fine, and I'll be disappointed if I shell out the cash for an upgrade, and that room acoustics are way more important. I don't think he's very accurate in his assessment, but I'd rather ask you guys. I'm basically assuming he's wrong, but under this assumption, still is the difference really THAT big between the Marantz and the Denon?

Second, if I do get the DRA-CX3 (which for only 570 on listenup right now is a real temptation), is there a way to use my Marantz as simply a switcher, and use the pre and power amps on the Denon? Giving up my switching capabilities would be terrible.

Third, for the extremely reduced $570 price tag on the Denon at the moment, would I be better off getting a standalone power amp at that price, and using my Marantz as a pre (which I know I can do)?

Thanks for taking your time to read this post, and please help!
sweetnumb
yogiboy's avatar
yogiboy
5,641 posts
 
The true power rating of a good amp will show a power rating 8 ohms from 20 to 20,000 hz and will almost double at 4 ohms. Now it seems like all smoke and mirrors the way they rate power ratings. I laugh when I see these cheaper amps with big impressive specs but they are just not in the same league as the real stuff.
sweetnumb OP
2 posts
 
All right. Well that makes a lot of sense Bob. Does it make a difference that my receiver isn't officially rated to drive 4 ohm speakers? I'm just having a hard time understanding the difference I heard, and I don't think room acoustics can account for that difference, as I heard amazing clarity and detail at extremely low volumes.

Perhaps the CD Player they used can account for the difference? It always seems ridiculous to me to be spending great deals of money on one, since the data is just digital, and seems it would either get read or not read. I have my PS3 setup to send the signal straight through digitally via the HDMI cable without converting it to analog. Perhaps I'm wrong about this concept though. I have also tried playing through a Panasonic Blu-Ray player we have with no audible difference, but I'm sure they are of relatively comparable quality either way.

The other possibility I can think of (aside from me just being crazy, which may very well be) is that the source material they used was just recorded and mixed/mastered flawlessly. If that's the case, then I'll need to find out what they were playing so I can experience it again.
mceljo
1,356 posts
 
I recently purchased a Pioneer Elite SACD player from Pioneer for a great price and have been really impressed with the sound quality improvement compared to my Integra 6-disk player and Samsung blu-ray player. The difference in redbook playback is significant. It's better, not just different. You might consider spending the $250 it cost to my door.

I don't know how much difference you'd hear going from the Marantz to the Denon just to get the 4 ohm rated capacity. My receiver swap had significant improvement in high current capacity and rated power so I have not heard the effect of high current capacity with lower power output. I'd expect that it MIGHT sound a little better, but really can't say.

The SACD might be a better bang for the buck.
Post removed 
More to discover