2. amps-preamps
  3. 1349886755

1.2k Output Impedance to 10k Input Impedance

I have a tube preamp with only single ended outs that does not have any output buffers and therefore a fairly high output impedance of 1.2k. My SS power amp has input impedances of 10k on RCA or 20k on XLR.

I have been advised by the designer of the preamp that anything lower than 50k or so will start loading down the line stage, so it would seem an imperfect pairing. My assumption is that at the very least I’d want to use the XLR inputs on the amp, as they present a 20k load to the preamp instead of the 10k vis the RCA inputs.

I have an RCA-XLR interconnect, but I’ve been told that simply using this will not result in a 20k load on the preamp and that the only way to accomplish this would be to use a passive transformer in line, such as the Jensen ISO-Max DM2-2RX.

For those that have experimented with these devices, do they result in any sonic degradation?

I'm wondering which might be the lesser evil – introducing an additional circuit and set of connections into the signal path via the DM2-2RX transformer, or running with a less than ideal impedance match between preamp and power amp. The answer is, of course, to try both and see, I'm just wondering if anyone has gone down this path before and what they found (heard).

Any inputs would be greatly appreciated.
128x128srosenberg
almarg's avatar
Ag insider logo xs@2x
almarg
9,670 posts
 
Hi Scott,

IMO, the impedance matching guideline is properly stated as follows (I'm quoting from myself in another thread):
Ideally the input impedance of the power amp should be at least ten times greater than the output impedance of the preamp, at the frequency within the audible range for which the output impedance of the preamp is highest. That frequency will usually be 20 Hz, as a result of the impedance rise caused at low frequencies by the output coupling capacitor most tube preamps use.

A factor somewhat less than 10x may or may not be acceptable, depending mainly on how the preamp's output impedance varies as a function of frequency, and also on the deep bass extension of the speakers.
The fact that the designer suggests 50K minimum tells me that the preamp's output impedance probably varies considerably as a function of frequency. And that it is much higher at some frequencies, probably including 20 Hz, than the 1.2K nominal figure (which I suspect is at 1 kHz).

The 20K balanced input impedance of the amp probably represents the sum of 10K input impedances on each of the two legs (i.e., on each of the two signal inputs that comprise the balanced signal pair). So using an RCA-to-XLR cable will not help, as you were advised.

Concerning the Jensen transformers, member Mitch2 has an excellent system and has spoken very enthusiastically in past threads about the results he has obtained with them. Atmasphere, on the other hand, has commented that in his experience they do have at least some slight artifacts.

Best regards,
-- Al
marakanetz's avatar
marakanetz
5,473 posts
 
In many cases trebble is the most affected area of impedance mismatch. In some cases you may develop lots of clipping even at low volume level and in some cases you'll be a happy listener.

Test your rig with piano music. Solo piano is ideal but you can also use small band or piano duos with violin, guitar etc at different listenable volume settings as you would listen normally.

You may also use some sort of autoformer between components, but with jeopardy to the bottom frequencies.
stevemcx
166 posts
 
Hi Srosenberg,

The information you've been given here is good, but it still leaves the question of how best to deal with the issue. I understand that this is not the place for advertisements, so let me simply say that I have developed a good solution for exactly this problem. It is functionally similar to the Jensen DM2-2RX but has been designed for use in high-performance audio systems. Please contact me if you would like more information.

Best regards,

Steve McCormack
SMc Audio
grannyring's avatar
grannyring
6,506 posts
 
I use a Jenson transformer to very good effect. Works like a charm with no negative effects on sound. Only $200 new!
joeinid's avatar
joeinid
658 posts
 
I have an Interocitor One aka Flex-Connect. It is made by SMC Audio and it is superb. I have the model that will step down the output because I have a high gain situation. It will accept rca or xlr on the input and will output rca or xlr, your choice. What's great about this? It can convert rca to xlr or xlr to rca and the amp sees a friendly impedance load. It works like a charm. I love it!!!
More to discover