AC Power Cord Wire Gauge

Let's do the math.

Take a stereo 100 W/ch amplifier, running in class A at 40% efficiency. That adds up to 500W draw. Much less than the 14Ga, 115V*15A=1725W capacity of the house circuit. Class A/B is more efficient and will draw varying current although most peak demand is supplied through power supply capacitors. Class D at twice the efficiency as class A, even if it had no capacitive reserve, would still be capable of 1725*80% = 690 W/ch (stereo) peaks.

Unfortunately, real life doesn't work so simply and I typically suggest not exceeding 50% the rating on most electrical for audio, if possible.

Consider, just for fun. my current system capable of drawing over 4000W and the electrical requirements.

The age-old question, "Why make PC's any bigger gauge than what's in the wall?" has a very simple answer: 'energy transfer' I'll explain:
When you plug your whatever into a wall receptacle, you are basically hooking it up (in parallel with other devices plugged into that same 'branch' circuit) across two buss wires (hot and neutral) coming from the panel. Think of this buss (usually a long length of Rom-ex in the wall) as a reservoir of water that under most conditions can never be emptied. Think of the power cord as a pair of tubes (hot conductor and neutral conductor) that you stick into this reservoir. Now water can flow (current) into one conductor, through the whatever, and back out the other conductor (and this process reverses 60 times a second because the current alternates.)

If the water is flowing through an amplifier, it's doing quite a bit of work, but in just a sixtieth of a second, it has to get back to the reservoir and then reverse direction! Sounds like an electron traffic jam waiting to turn into gridlock! To insure this doesn't occur, you provide many many lanes (or in this case, large conductors) and you lay them out so drivers aren't blinded by oncoming headlights (inductance and capacitance) slowing things down unnecessarily ;-) Simply put, the energy transfer requirements, back and forth between the device and the reservoir, are quite different in nature than what it takes to keep the reservoir full.

At the risk of starting an ecclesiastical controversy (which I hope will not occur), I must respectfully but completely disagree, because as an electrical engineer I believe the quoted perspective would be severely misleading to the original poster and to others who may read this.

Simply put, there is no basis whatsoever in science or engineering for viewing the ac outlet as a point of demarcation between a reservoir, and a set of tubes or whatever that draws water (or in this case current and power) from the reservoir.

The wiring system is just that, a system. Energy is being transferred back and forth at a 60Hz frequency through the house wiring just as much as through the power cord. Increased resistance in the house wiring, due to smaller gauge or greater length, will produce a voltage loss just as readily as in the power cord. And in fact most likely to an even greater degree (since the combined current draws of multiple devices are likely to be flowing through it, rather than the current draw of just one device, and voltage drop equals current times resistance).

As I said earlier, there may be subtle reasons why subtle sonic differences may result when 10 gauge power cords are hooked into 12 gauge house wiring, but the differences are not due to the gauge per se.

Regards,
-- Al

Al -- your explanation represents sound engineering, and I know it well; in fact some embrace those principals to the point of hardwiring their amps' power supply right back to the panel, convinced that strategy will provide the very best energy transfer. Good for them;-)

A real scientist would not be so sure. The facts are a little different than you imply:

As I said earlier, there may be subtle reasons why subtle sonic differences may result when 10 gauge power cords are hooked into 12 gauge house wiring, but the differences are not due to the gauge per se.

First, the difference is NOT subtle (you should try it ;-)
Second, the effect of using larger (and larger!) gauge conductors is the same, regardless of the brand or topology of the cord -- the sonics of the amp will "open up" dramatically! In my own experiments, this improvement continued incrementally up to 8 AWG which is as far as I went, but PS Audio (I think) makes 6AWG PC's, which might make sense to some ;-)

So, counterintuitive or not, it IS the gauge. Why? Well maybe Quantum physics will explain it one day ;-) I'm certainly willing to accept my own explanation as flawed (from an ENGINEERING standpoint) but it's the best I can conjure until science discovers the REAL reason. It's just a matter of time, I'm sure.
.

Nsgarch,

I take no position on your findings that "the effect of using larger (and larger!) gauge conductors is the same, regardless of the brand or topology of the cord." I have no reason to doubt that your sonic perceptions were accurate, although I'm sure that there are many others whose listening experiences and perceptions would both support and contradict your conclusions.

I would certainly keep open the possibility that there are as yet unidentified design characteristics among audiophile-oriented power cords that tend to correlate with gauge, that might SEEM to produce a correlation between gauge and performance.

Obviously science and engineering certainly cannot, at this point, explain everything about why we hear (or think we hear) what we hear. But they can explain a lot of things. And my basic point, I guess, is that having no explanation is far preferable to having an incorrect one. Because the incorrect perspective that can result from an incorrect explanation can negate the value that good science and engineering CAN bring to the table.

Best for the holidays and new year!

-- Al