EG., see my post above for starters.
Are or is this cable using twisted pairs?? In essence, did you simply run one cables then to use as a dedicated line for such a circuit? Did you keep the positive (hots) still twisted together? Same for the Neutral and ground, were they twisted together?
You should have put another neutral in there as you went with using two different phases. Albeit, things should work anyhow.
Ive seen worse BTW.
If so the buzzing issue you experience without the use of the conditioner is due to some ground loop issue somewhere in the house. Plain and simple.
Keeping the pairs twisted together at first made me think youve added some inductance along the way too that would not ordinarily be there usually. But thats not the deal.
As you ran two twisted pairs of #10 AWG stranded the wire alone should stand up to 30 A. Solid #10 = 25A max. Stranded #12 = 25A., and solid #12 = 20A max. the thinking behind why use the appropriate gauge wire is this, heat as well is a factor which increases current. An appropriately sized conductor will transmit and conduct that heat energy sooner than will larger gauge conductors.
and thats what we are trying to prevent here with proper ckt applications fire, not necessarily saving the causer of the overload, but the rest of the array and perhaps lives.
Had you ran two runs of grounds and commons, I think it would have been more to code and better overall at least in my area, thats code.
In effect you have ONE dedicated line attached to two breakers for all intents and purposes, and again, it should work but its the cheapie/temp way to do things and it pays to do electrical things properly.
To find the issue, turn off everything BUT the breaker controlling the thing thats buzzing. Turn on the thing. See if it still buzzes.
If so its a ground loop and likely comes from either your Pay TV svc. Or your phone svc.
If it doesnt buzz while its the only energized thing in the house, begin flipping on breakers on that phase, one at a time continue to the opposite phase, until you find the ckt to which the ground can be attributed.
Worse case scenario would be the ground issue is an accumulation of household items being used in which case l3eaving on the amp, and energizing more breakers/circuits will increase the level of the hum/buzz as you go along.
The choices once the item causing the issue is found are:
Call an electrician.
Disconnect things from the ckt which is causing the GL until you get to the actual culprit and never use that again. Cell phone charger, UPS for the PC, rheostat (lighting dimmer) , etc. or get a better one.
If the buzz is there with everything else off, it is most likely the cable TV or phone to make sure, disconnect the coax feeding the Sat/cable box and see if you still have the buzz/hum.
In that case a transformer can be put inline with the coax feeding the cable box. Sometimes right at the box, or outside the house where the coax run begins.
If its the phone install another ground rod explicitly for the phone. I wont guarantee this move, but Ive seen it work. Disconnect the orig ground ckt, and drop the new rod several feet away from the orig one. 10 ft. should do.
Lift the ground from the receptacle the amp is plugged into. Either by a cheater plug (both hot & common but no ground pin), or by removing it from inside the outlet itself.
If you chose to put breakers one on each phase because that was the only available unused slots. There is a work around for that as well.
They are called Wafer breakers. Half the size of standard breakers so that two fit into the same space as ONE regular breaker. They come in various ampere & voltage sizes too. Thus allowing you to put both ded lines onto one phase, which was recommended.
I must also say here at this point, I was an electrician in my past. Mainly industrial and commercial efforts some residential now and then on the side. I gotta say here you really should contact a card carrying sparky for this event, but if you feel compelled to proceed, it is surely at your own risk.
Not trying to scare ya IM just CMA.
Good luck. Hope that helps.
Are or is this cable using twisted pairs?? In essence, did you simply run one cables then to use as a dedicated line for such a circuit? Did you keep the positive (hots) still twisted together? Same for the Neutral and ground, were they twisted together?
You should have put another neutral in there as you went with using two different phases. Albeit, things should work anyhow.
Ive seen worse BTW.
If so the buzzing issue you experience without the use of the conditioner is due to some ground loop issue somewhere in the house. Plain and simple.
Keeping the pairs twisted together at first made me think youve added some inductance along the way too that would not ordinarily be there usually. But thats not the deal.
As you ran two twisted pairs of #10 AWG stranded the wire alone should stand up to 30 A. Solid #10 = 25A max. Stranded #12 = 25A., and solid #12 = 20A max. the thinking behind why use the appropriate gauge wire is this, heat as well is a factor which increases current. An appropriately sized conductor will transmit and conduct that heat energy sooner than will larger gauge conductors.
and thats what we are trying to prevent here with proper ckt applications fire, not necessarily saving the causer of the overload, but the rest of the array and perhaps lives.
Had you ran two runs of grounds and commons, I think it would have been more to code and better overall at least in my area, thats code.
In effect you have ONE dedicated line attached to two breakers for all intents and purposes, and again, it should work but its the cheapie/temp way to do things and it pays to do electrical things properly.
To find the issue, turn off everything BUT the breaker controlling the thing thats buzzing. Turn on the thing. See if it still buzzes.
If so its a ground loop and likely comes from either your Pay TV svc. Or your phone svc.
If it doesnt buzz while its the only energized thing in the house, begin flipping on breakers on that phase, one at a time continue to the opposite phase, until you find the ckt to which the ground can be attributed.
Worse case scenario would be the ground issue is an accumulation of household items being used in which case l3eaving on the amp, and energizing more breakers/circuits will increase the level of the hum/buzz as you go along.
The choices once the item causing the issue is found are:
Call an electrician.
Disconnect things from the ckt which is causing the GL until you get to the actual culprit and never use that again. Cell phone charger, UPS for the PC, rheostat (lighting dimmer) , etc. or get a better one.
If the buzz is there with everything else off, it is most likely the cable TV or phone to make sure, disconnect the coax feeding the Sat/cable box and see if you still have the buzz/hum.
In that case a transformer can be put inline with the coax feeding the cable box. Sometimes right at the box, or outside the house where the coax run begins.
If its the phone install another ground rod explicitly for the phone. I wont guarantee this move, but Ive seen it work. Disconnect the orig ground ckt, and drop the new rod several feet away from the orig one. 10 ft. should do.
Lift the ground from the receptacle the amp is plugged into. Either by a cheater plug (both hot & common but no ground pin), or by removing it from inside the outlet itself.
If you chose to put breakers one on each phase because that was the only available unused slots. There is a work around for that as well.
They are called Wafer breakers. Half the size of standard breakers so that two fit into the same space as ONE regular breaker. They come in various ampere & voltage sizes too. Thus allowing you to put both ded lines onto one phase, which was recommended.
I must also say here at this point, I was an electrician in my past. Mainly industrial and commercial efforts some residential now and then on the side. I gotta say here you really should contact a card carrying sparky for this event, but if you feel compelled to proceed, it is surely at your own risk.
Not trying to scare ya IM just CMA.
Good luck. Hope that helps.