avs9
Responses from avs9
| Sumiko tonearm rewire Hi, wonder if I will need the flux, never solded wires these thin, or the using the Mundorf I wouldn't need that? They say the wire does contain the flux but I wonder if I's better to apply some of that? I am curious to know if there are any drawb... | |
| Colibri Light Weight Gold on RS212D - wow Thanks, Geoch, tubes part was very helpful since I am in the middle if deciding which ones to go with for CJ PV-12 pre-amp phono. So far I am planning on RCA 5751 blackplate TRIPLE MICAMazda France 1964-1965 vintage 12AX7S12AX7 Telefunken smooth p... | |
| Colibri Light Weight Gold on RS212D - wow Dear Geoch, thank you for the response. Mine is 0.28 mV, gold coils. I purchased it following Raul's advise and I can say I don't, even with my well under avg setup the little beast shows remarkable.I yet have to listen for a few weeks, I need to ... | |
| best bass or close to that 12AX7 tube Thanks folks, I guess you are exactly right - buy and listen!And that's fine. I read through a lot of posts here and quite a few of them state different tubes behavior. To the point about the RCA - actually one seller did state the same about the ... | |
| best bass or close to that 12AX7 tube Hi,Thank you for the response. Yes, did go there actually quite a lot for the last few days, spoke with Brent, he says Telefunken will sound a little flat as bass goes comparing to Mazda labels, which cost about twice as more. I won't mind the pri... | |
| Sumiko tonearm rewire Wow! Never imagined the coating must be removed from litz wires. Please forgive my ignorance - why? OI thought the idea of litz strands was to minimize the 'skin' effect, but if coating taken off you got one thicker conductor? Or the flow will sti... | |
| Sumiko tonearm rewire Cousinbillyl, Sorry, forgot to ask you - the 44 awg wire you mentioned - that was not litz wire, was a single thread, correct?Thank you | |
| Sumiko tonearm rewire Thanks a lot, Cousinbillyl,this is really helpful.By the way, the old Sumiko wires (now gone as I mentioned) were silk coated, which confirms what you just said.I am actually excited about getting into this, arm rewire I mean, your short intro wil... | |
| weights on Sumiko MDC800 versus MMT,FT3 Thank you, Nandric, the arm on MDC800 is 10.5 mm as my micrometer shows, the answer about that I got from someone selling FT3 on ebay was 'about 12-13 mm'. On the good side it is not less, but it doesn't look like they are interchangable as is. Re... | |
| Sumiko tonearm rewire Well, Decided to take the re-wire route and here is the result.Plunged into BritAudio rewire service, asked before shipping if can be done, the answer was positive.Now got the arm back not wired with the refund check minus shipping, the note says ... | |
| Orsonic headshell source? Thanks, folks.I sent email to Albert.Speaking about Ikeda headshell - I didn't find the 'RS', there is one named IS-1R, looks impressive.Syntax - looks like you had a chance to compare this to others, what cartridge you mounted on it? Regards | |
| I am set on all but speakers, need advice on those Tabl10s - yes , just sit down and listen, nothing else at this time. No background at allThank you | |
| I am set on all but speakers, need advice on those Thanks, folks, I think I have a much better starting point right now with your feedback. Looks like I will need to backup a little and do some more legwork and do the same I did with pre-amp and amp - bring another pair of speakers to my place and... | |
| I am set on all but speakers, need advice on those Thank you all, folks.To Manitunc - you are correct, I did look at Liuto. Though while I was looking through posts here I saw a couple stating that the GPH being an older issue somehow had more sweetness to it then the new ones like Liuto. Have not... | |
| audition copper/silver arm wire in New York Frogman, yes with personal emails now sort of not working (at least for me) it is not that easy to get in touch with someone. But whenever you have time it is 9143099091 my cell, would appreciate.For now I decided to go with copper in my old Sumik... |