gvoth
Responses from gvoth
| Your most indispensable "tweak"? A few of my essentials:Sorcer X4Novum PMR IIBybee Quantum Clarifiers | |
| Well Tempered Labs Record Player, thoughts on a used one? I love Well Tempered tables... I know them very well and have made clones of their arms for personal use on both my idlers. Both the older and newer designs are brilliant and DO punch well above their price point. I have had the WTT since buying i... | |
| low mass tone arm suggestion sub $1k used Home project! Make your own Well Tempered style Simplex arm with a carbon fiber wand thru whole golf ball or or Amadeus-style arm with wand thru cap on top of half golf ball. Considered medium mass and handles a slew of different cartridges - add ... | |
| Is there an affordable long run XLR preamp to amp cable out there? Thanks for the feedback fella! | |
| Well Tempered Simplex arm and wiring Finished the table. Fabulous. | |
| Well Tempered Simplex arm and wiring Can any WT Simplex owners measure their arm for me? I'd like to know the exact length, minus the rubber stoppers on each end. I'd also like to know the distance from the tube front to the center mounting screw for the cartridge bracket... Lastly, ... | |
| Well Tempered Simplex arm and wiring Can WT Simplex owner tell me the exact length of the armtube (not counting the black rubber stoppers of each end)? Can you then tell me the distance from the front of the armtube to the center the mounting bracket for the cartridge? Thanks in adv... | |
| Well Tempered Simplex arm and wiring Sorry, I see you told me the arm is slightly smaller than 1/4" d... which probably makes it 6mm. My brother was bothering me about my arm being too thin (6mm) so I ordered 7mm carbon fiber rods. Probably should have left well enough alone... Can y... | |
| Well Tempered Simplex arm and wiring Yeh, it's a great azimuth solution. When I modded an original WT arm and then built my own clone, I saw both partial twist and full twist online... and finally modded my arm with a thinner 1/4" suspension post, making sure to give the grommet a fu... | |
| Well Tempered Simplex arm and wiring In the past, I've used a 6mm od diameter carbon fiber rod (4mm id). 6mm us slightly smaller than 1/4". From what I see, a standard arrow shaft is 5/16" od, which would make it 7.9mm od. Any way you can confirm your arm's diameter? Also, how does t... | |
| Well Tempered Simplex arm and wiring Understood - no need to unmount anything! I see that top hole as where a screw inserts down into the ball half, then the arm tube is inserted. Of course, they could be joined with epoxy, which is what I might do. On an assembly line, screws and no... | |
| Well Tempered Simplex arm and wiring mr_m, it dawned on me that I could 3D print a similar connector to what the Amadeus ll uses to attach the ball and arm (why not make it more like the upscale model rather than the Simplex...). Can you tell me a little about the piece that connects... | |
| Well Tempered Simplex arm and wiring My base for the Simplex plinth turned out great - it's the same 15" x 15" x 1.25" size of the plinth - a matte black metal picture frame filled with 3 layers of ply. I moved the squash balls to the bottom of the base and separated the base and pli... | |
| Well Tempered Simplex arm and wiring The Simplex plinth I bought has the set screws. A friend is making the pot for me according to your measurements (he’s printing it 3D out of grey plastic). I bought a regulated AC to DC power supply and the motor turned nicely. I am making the pil... | |
| Well Tempered Simplex arm and wiring Correction, I’m making both Denril and aluminum versions of the pillar. |