Bi-Amp Basics - NHT 29s


Ok, I think I know what to do here, but I wanted to get thoughts and opinions. I have a decent but dated NHT theater system consisting of 2.9 fronts, AC2 center, and HDP2 Surrounds. I am looking to improve the front sound state by upgrading to a new amp that will drive all five speakers, but using this new amp for only the top end of the 2.9 fronts, and utilizing my current amp to drive the bottom. To get this done, I need an RCA spliter to send the same signal to both amps, and then wire each amp to either the upper posts, or the lower posts (Correct)?

Just checking...

Anyone care to recommend a 5-channel for the NHT system (Upper only on the 2.9s), and a 2-channel for the bottom of the 2.9s?
jbryngelson
That makes sense to me now. Luckily, the Parasound does have gain control, so I can calibrate it to match what ever amp I put to the top.
Well as Rodman touched on above, you would have to have amps on the top and bottom ends with equal gain if you didn't use the X2 as they would be sharing the same volume control, so unless the tube amp and Parasound you want to use just happened to have matching gain, which I highly doubt they do, you really can't without the X2.

Go to NHT.com and download the X2 owner's manual for more on this.

Hope that helps.
Im a bit confused. If I did not want to use an active crossover, how would I bi-amp the 2.9's?

I am thinking of using Tubes for the Top end, and my Parasound for the bottom end.
Follow Markruss' advice of using an active crossover to bi-amp. Power amps w/o active filtering MUST have matched gain AND sensitivity to provide an accurate frequency response when used to bi-amp(or at least input attenuators). An active crossover will give you the ability/flexibility to balance whatever power amps you choose with one another.
Get a NHT X2 active crossover and a pair of NHT A1 monoblock amps to bi-amp the 2.9's subs. They are much better than the older SA-2/SA-3 amp/crossover combos. This will also give you more control over the bass by allowing you to dial in flat response for music, and at the same time, a little extra "boom" for movie soundtracks' LFE content. Then, for the 2.9's upper frequncy drivers, since they are high passed at 100 Hz, power rating simply isn't as critical. Go for quality over quantity.

Also, replace those dipole HDP2 surrounds with a pair of new Evolution L5 on wall surrounds on closeout from ListenUp.com, which are phase-matched to the 2.9s/AC-2.

If you do these things, I guarantee you that you will be happy with your system for many more years to come.
Another Option
Use two Aragon 8008X3's and pick up a NHT SW3 Slave and you would have one awesome 5.1 and 2 channel system. The Aragon's work great with the NHT's also. Not sure if these are within your budget. But just a suggestion.
What you might want to consider, using the five channel amp to drive the 2.9's and the AC2 and your current amp to power your surrounds. Use four of the channel to vertically drive your 2.9's and the fifth to drive the AC2. This would make for a more consistent front soundstage. Then when possible find a matching two channel version of the five channel amp. Another option 2 Two channel amps to vertically bi-amp the 2.9's and a three channel amp to power the surrounds. I've found the McCormacks to work well with the NHT's. I have a pair of the 2.5's connected to a DNA-1 in my spare room. If you decide to use the older McCormack's DNA's I would recommend the DNA-1's. Heard the 2.9's with the DNA 0.5's and it was really bass shy.
Depending on what connection options your amps have, you may also be able to daisy chain the amps so that you don't need a splitter.

Keep in mind that when bi-amping, the amps need to have the same gain