Can upgraded power cords help my setup?

Measure the speakers distance to walls and floors - avoid similar or doubled distances.

Have lots of glass, heavy furnishings, a rack between the speakers?  Look into that too.

Get a test CD, and rent/buy a good SPL meter

Play your favorite recordings that you have heard on distinctly better equipment and figure out if there are trends in your system.

Bring in new cables, but have them switched by a friend so they are blind to you.  Have them mark your preferences.  In most cases you won't have one, given audio nervosa and the ego pride of new and expensive gear.

I have heard cables sound different at times, with a preference.  As a hobbyist for over 40 years and dealer for years I've heard a lot, but never have I heard cables do a fraction of what a properly set up ASC trap room does, nor come close to overcoming a poorly set up room, or mediocre equipment.

Said another way, its possible cables may help tune your system to a higher level, but it's at best a cherry on a desert, the other 6 courses of the meal come first.

Drawding, you say:

"Also keep your PC away from your interconnects or if they must cross have the cables at 90 deg to each other."

Here you locked onto one way well designed cables can help your "system" by helping to address the cluttered "cable ecosystem" often found behind our gear.  I cannot tell you how a good PC does or does not "clean up" power from the wall to your equipment (garbage into cable - 4 star power dinner out? OK, maybe), but it only makes sense that reducing stray electrical fields and interference between high current cables and low current cables in the vaccinity of your amp and source can yield real gains in fidelity.  Better cable geometry and shielding across all applications behind your gear helps solve the same problems as keeping "your PC away from your interconnects" in physical space.

Al, terrific input here as usual.  I agree with your assessment of the unique applications presented by the LS50's.  Two issues come to mind:

One, there is unlikely very much other wire clutter behind your speakers, so the benefit of a better shielded PC to reduce interference with IC's and speaker cables all exiting the same amp or reciever i describe above is essentially moot. This leaves a more solid connection to speaker and power outlet as a potential advantage of a better cable with better connectors, along with improved match of metallurgy, dielectric and wire geometry with the properties of what are really very complicated speakers with many things going on inside them as Al notes.

Two, given the complex devices, I might look at PCs that would work well with modestly powered but quality switching AVRs that contain both amplification and digital circuitry.  You need to supply juice for 230wpc of switching power, right?  Suggestions by others above to focus on smaller gauges common for digital applications versus heavy "garden hose" PCs seem warranted as taming digital artifacts may be more important than raw current for this application, and very heavy cables on small speakers may present physical stability issues. But YMMV.

In my experience, better cables across the board make a positive and sometimes radical difference in sound, but as suggested by others, you just have to try several solutions to see what works best in your application.  I like the idea of contacting the Cable Co. and asking their advice for 2-3 cables to send you in your price range to try with the KEFs (and the Node?) and listen for yourself to see which cables sound better, if any, compared to the stock PCs.

Finally, you may want to try at least one power conditioner and move between the speakers and the Node 2 in order to see if that helps improve your sound. You may decide you need two if the Node and speakers are far apart and both show benefit.

Good luck,

kn

In the last month & a half I've made a few power cords that I'm very impressed with using Oyaide Tunami wire (purchased from Chris at VH Audio) and Neotech connectors from Parts Connexion. The wire is $30 a foot & the ends are $25 each (they are a discontinued model from Neotech that retail for $70 each). All that said, you can make a very good 4' power cord for $170 plus shipping. These PC's replaced Pangea 14's & a 9 as well as some older Tribularies. They are better in every way, not even in the same ballpark. In regard to the statement above about updating your equipment instead of wire; I've been using the same phono amp, preamp, power amp, & speakers for 10 to 20 years (depending on component), & can tell you first hand that wire matters. I like the Oyaide PC wire so much that I purchased more of that last week to try as speaker cable. Pretty dumb huh, not... Although it only has about 30 hours on it now, that has also made a large improvement to the sound. That wire replaced Morrows SP5 cable, which is also very good. I should add that my whole system with the exception of the sub, is run through a very large Exactpower transformer so that could also be why the difference in wire is so profound. I really don't know, but the investment was worthwhile. 





           

This was posted by Cnet reviews on internet: highly respected reviewers of high end Audio:

Power Cables

High-end power cables are seriously a thing. I'm not kidding. If you believe changing the power cable in your gear will improve the audio or video...I have an island I want to sell you.

In short (so to speak), power cables have no effect on audio, video or any other kind of fidelity.

@pennsy,

This thread is no place for real electrical knowledge and logic. There's people here referencing Shunyata papers as proof of the science behind high-end cables.