For anyone seriously considering deploying a distributed bass array system in their system and room, I believe the thought of where to locate 4 subs is a common concern.
It was definitely a concern of mine until I went through the rather extensive setup procedure that determines the ideal spot for each sub. I'll describe my experience so that readers can better understand the process and how these concerns were remedied in my installation:
My living room serves as the home for my combination music listening and 5.1 HT system.
It is 23 ft long and 16ft wide. My 65" hdtv is wall mounted roughly in the center of the front 16 ft wall. There is a Magnepan 2.7qr panel (each 6 ft tall and 2 ft wide) on each side of the tv that are both about 4 ft out from the front 16 ft wall and 1 ft in from each 23 ft side wall. There is a Magnepan CC3 center ch speaker centered above the tv that is wall mounted. All components reside on or in a 5 ft wide by 1.5 ft tall audio cabinet located below the tv and against the 16 ft front wall.
The primary listening seat is centered on the rear 16 ft wall with a 7 ft sofa along the right 23 ft wall and 2 chairs along the opposite 23 ft wall. There was not a lot of open space in this room when I began the setup procedure.
The setup procedure is:
Sub#1 is hooked up and placed on its back (driver facing the ceiling) at the normal listening position. Music is played that has good and repetitive bass.
Walk around the edges of the room and determine exactly where the bass sounds best to you.
Attach the 3 spiked footers to Sub#1 and position it upright facing the nearest wall to the spot you determined the bass sounded best.
Sub#2 is hooked up and placed on its back at the primary listening position. With sub 1 & 2 playing, continue walking around the edges of your room and determine again where the bass sounds best to you.
Attach the 3 spiked footers to Sub#2 and position it upright facing the nearest wall to the spot you determined the bass sounded best.
Repeat this procedure for sub 3 & 4.
Small positioning adjustments may need to be made for each sub due to avoiding furniture and the WAF.
Once completed, final sub hook up is done in parallel:
Attach a single wire from the amp's speaker A's pos. output terminal and to Sub#1's pos. input terminal.
Attach a single wire from the amp's speaker A's neg. output terminal and to Sub#2's neg. input terminal.
Attach a single wire from Sub#1's neg. input terminal to Sub#2's pos. input terminal.
Attach Sub 3 & 4 using this parallel method on the amp's speaker B's output terminals.
I ordered single, high quality and low gauge speaker wire along with the sub system for a very reasonable price. Once the ideal locations for the subs was determined, I drilled holes in my room's floor to the crawl space below, and was able to hide the connecting wires.
The final positioning turned out not to be an issue, with the best sounding positions actually being discreet and unobtrusive. The 2 front subs are each located directly behind my main panel speakers and are not even visible from my primary listening position.
The 2 rear subs are each located along each 23 ft side wall about a foot in from the rear wall. The left wall sub is concealed from view by a leather recliner and the right wall sub is concealed behind a large end table. My primary listening seat is between these 2 rear subs.
I should mention I've never had my system/room analyzed using a mike and software. From my purely subjective perspective, however, I'm confident the results would be good since I spent hours on the setup and critical listening from all six listening positions in my room. I would suggest this type of sub system as a viable alternative for anyone considering investing in one or more quality subs. The system is rated clean at 113 decibels at 20 hz. I've often heard and felt it go this deep. It feels and sounds clean and right but I can't verify the frequency, decibels or lack of distortion.
Sorry this turned out so long and windy,
Tim