Get Stoned

Sorry Albert et al .....I was in a hurry to get to my system and mistyped...

Stringreen, I respect your opinion based on the totality of your contributions here, which is why I asked to know more about the Terrastones. Skepticism is usually not inappropriate in this hobby, but because you like the Terrastones, I would make the effort to learn more about them.

I made some footers for my slate-plinth Lenco in the following way: I purchased small-size cans of Mandarin Orange slices in water, three of them. To the bottom of each I attached some Black Diamond carbon fiber conical footers using double-sided tape. (I had a set given to me.) The bottom surface of the slate plinth is placed againt the "top" side of each of the 3 cans, and that's it. I had noted that the anti-skate weight of my Dynavector DV505 tonearm would readily start swinging whenever I walked past the turntable, even though it is sitting on a very large and heavy Adona rack, on one of their damped granite shelves. The can-footers have nearly completely damped out that phenomenon. I think it would be even better if I were to insert some spacers, so that the bottom surface of the slate plinth engages only the top surface of each can, not including the raised edge around the circumference of the top. Total cost: about $6 plus the use of the Black Diamond cones. Any such conical feet would do the job, IMO.

Theory: the Mandarin Orange slices in water provide a sink to absorb and dissipate vibrational energy entering from below. The orange slices serve to break up any regular wave motion of the water which might otherwise transmit to the plinth. (By the way, it looks more professional if you remove the labels from the cans, could be even more expensive looking if you paint the cans black, white, or silver.)

I agree, its hard to imagine this would make a significan difference, but I firmly believe everyone's system has strengths and weaknesses and improvemnts for some might not be for others and vice-versa.

That being said, as a former VPI Aries 3 and SDS owner, maybe the SDS 'acts' like an amp. Minimize the vibrational aspects to the cabinet of the SDS and it could conceivably improve it's ability at volatge control and thus speed control to the motor. Better speed control equals better sound.

What would be interesting is if someone would us the Feikert iphone speed app or another measuring device and measure the speed accuracy of the SDS with and without the terrastones. That would definitely confirm what Stringreen could be hearing.

I do own a VPI classic 1 but, not the SDS controller. I am powering my classic 1 with the purepower 1050 AC regenerator. The purepower unit does output a true 60hz/120v feed. I haven't detected any flaw in speed stability so far. If it is off speed I can't detect it audibly. I would like to try the SDS to see if it would make an improvement.

The reason I responded to this thread is beacuse I have just ordered some terrastone products and thought I would share what information I know about the material. According to Dan @ edensound, Terrastone material is a very dense isolation polymer. He said it serves a dual purpose of rejecting outside vibrations as well as damping vibrations originating from the source component. I'm not sure exactly how this is achieved, you would need to ask dan about that.

I tried some of dan's brass bearpaws on my classic one. They did make a very noticeable improvement but, I had some low frequency vibration problems due to the rigid setup. Dan suggested the terrastone because it does a better job of isolation than the brass. I have ordered a custom terrastone platform and a set of terrastone footers for my VPI table. I will post some pictures and my impressions of those products after I integrate them into my system.

I would assume that the terrastone polymer would do a great job of isolating the SDS unit as well. I can't understand how isolating the SDS could improve the sound though, as it is a speed controller and is not directly in the audio signal path. I'm am not saying it doesn't work, I just can't understand how. I guess don't knock it till you try it.

Another thought...

Try this: take the belt off the motor so that the platter won't move, lower the stylus onto the platter, switch on you amp and turn up the volume. Now switch on the motor and you should hear hum.

The hum will come and go as you switch on and off the motor. The hum isn't electrical, it is from the vibration of the motor transmitted through the table and shooting back up to the platter from the cone feet.

Try the above with footers under the SDS and then not. If you hear less hum when the footers are on, then the SDS and Power cable are acting as a vibration sink for the motor.