2. amps-preamps
  3. 1294111753

Good tube preamp for McCormack DNA 500???

I just purchased a dealer demo McCormack DNA 500. I have decided I want to pair it with a tube preamp and I'm looking for the best fit within my price range ($2500 new or used). My research has uncovered a thread here on Audiogon that quotes the designer, Steve McCormack, recommending that any tube preamp paired with the DNA 500 (10k ohms input impedance) should have less than 800 ohms output impedance and the "lower the better".

Heeding this advice here is my top five: (1) Manley Jumbo Shrimp @ 50 ohms; (2) Purity One @ 180 ohms; (3) VAC Stantard LE @ 350 ohms; (4) Joule Electra 150 MK.II @ 400 ohms and (5) Conrad Johnson PV 15 @ "low" (can't find specs.) ohms. These are all currently for sale on Audiogon and are used except for new Manley J.S.

The rest of my system consists of Aerial 10-T speakers with mid-$$-range Synergistic Research cables and a highly modded Anthem CD-1 digital source. I prefer a warm, rich sound with no rolled off highs, mids or bass. Remote control is a must but I don't have a high care factor on balanced vs. single ended.

I would appreciate comments from anyone who has had success with a tubed preamp and the DNA 500 or anyone who because of their vast knowledge or experience with such matters cares to comment. Thanks in advance for you input!
shoff
unsound
7,329 posts
 
The SF 3 will probably have the lowest output impedance you'll find in a tube pre, it's DC coupled, so DC offset isn't as likely to damage the amp, it has true differential balanced outputs to match the true differential balanced inputs of the McCormack DNA 500. Oh yeah, it also has compartmentalized separate power suppl(ies), balanced and SE inputs/outputs, tape loops, remote control, headphone amp output, and most importantly is one of the most neutral sounding tube pres your likely to find.
rootmann's avatar
rootmann
78 posts
 
I use a VTL 5.5 feeding my DNA-500 into a pair of Magnepan 3.6R's. Works well for me.
stevemcx
166 posts
 
Hello Shoff -

I hope you enjoy your time with the DNA-500. It is a fine amplifier, and happens to be an extremely good match for your Aerial 10-T speakers. Don't worry too much about finding the lowest-possible output impedance preamp. You do need to keep an eye on this spec, and I suggest you stay below 800 Ohms for best matching. But once you are under that value you should be fine, so look for the preamp that otherwise best suits your sonic and feature requirements.

Best regards,

Steve McCormack
SMc Audio
shoff OP
133 posts
 
Thanks to all of you who have posted so far. You have given me more options to consider as well as confirming a few of my original thoughts. When I invited comments from those who had "vast knowledge and experience in these matters" I had no idea that I would hear from the Master Designer himself Steve McCormack! Thank you so much Mr. McCormack for sharing your insight and for the reassuring words regarding the synergy between the DNA 500 and the Aerial 10-T's. That is exactly what I wanted to achieve.

As you know, it is virtually impossible to listen to all of these products before purchasing. That's why forums such as these are inspensible to music lovers. I have not made up my mind yet, but until I do, please keep your suggestions and comments coming! I'll post when I have made my decision.
jim_swantko
301 posts
 
I used the Cary SLP-05 with 10T's with excellent results. I wasn't using the DNA-500 but am sure they would sound wonderful together.

The 10T's need help keeping the bottom end under control. The SLP-05 was one of the best tubed preamps I have used in bass performance. The rest of the performance is also very, very good.

If you can audition one I would seriously consider the SLP-05 if it works with your budget. It's not excessively "warm" per se, but does have the midrange magic which you may be referring to. The extension top and bottom are outstanding for a tubed product in my experience.

Good luck with your search!
More to discover