2. cables
  3. 1335297906

High Fidelity Cables CT-1designed by Rick Schultz

In December 2011,I wrote that High Fidelity cables led by cable designer Rick Schultz was putting together a new cable.The cable came to market as CT-1.The CT-1 has FINALLY made it into my system!I had obtained a version of the prototype that Rick had been working on.It blew my previous reference Genesis by Virtual Dynamics.I thought I had finally found my end with this cable.This prototype delivered to my ears "Nirvana".Could I be at the end of my quest for the ultimate sound?
No. I received two pairs of CT-1 to replace my prototypes.They went into the system this past Friday.Unable to dedicate time until Sunday listening,I stole a few moments,ducking away from company with anticipation.My guest could tell even with the music set for"ambiance"something was intriguing and I was in for a treat!
The experience:
First off,CT-1 was very user friendly.Installation was simple;the cable is very nice and light.The female RCA fit beautifully unlike any I had found in other cable.It was secure and reliable.It seemed much thought was dedicated to developing a designer fit to an aesthetically stunning RCA connector.Install entailed a few wiggles to ensure what seemed like a compression fit on my RCA.
It was 2-3 hrs. for the 1st step of break in to be complete.At that point I had something different!Today,although they only have 10-12 hrs. on them,I can`t put into words how much my system has transformed.Believe me,I loved my prototypes.However....there is simply no comparision.
The clarity and sound is so natural.
The soundstage is like nothing I ever heard.Resoulution is breathtaking and inner detail is simply hard to believe possible.
The sound has transended and now it simply does not seem as thought I have speakers.
My system is musicians playing music.
I am told with time they will improve and I trust that as it was revealed with the prototypes.I wanted to share my thoughts with you that now.
Unequivocally,a testament to High Fidelity,as the name declares.
High Fidelity Cables for me,the last word on it,after 12 hours!
Truly Amazing

Al
alpass
agisthos
507 posts
 
The new amp is the latest circuit design by Steve Keiser who did the KST-150 for Luminance Audio. No negative feedback or emitter resistors.

Built to a much higher standard than the earlier amp with the choicest parts and magnetic conduction technology. I heard its going to be expensive...
ketcham
92 posts
 

On my Allnic D5000 dac I have balanced cables and HF reference cables in place. Both hooked to the pre-amp. I can immediately go a-to-b, b-to-a. The pre to amps are HF reference cables.

The result: Much wider, deeper soundstage, better inner detail, 3-D imaging. 20% louder too--like the proverbial voice of GOD. I know the output voltages are spec the same.

If someone is to purchase one cable, I would say source to pre is most effective.
fluffers
78 posts
 
Guys- Just got 2 sets of used Ultimate interconnects- Question on breakin- On these cables does the system have to be on OR is just letting the system settle with the magnets be enough??- hate to leave the tubes burning if not necessary- thanks
fplanner2000
616 posts
 
They will break in 10x faster with the system on. Just sitting there pretty much does nothing, relatively speaking, in my experience.
tbg
5,263 posts
 
Fluffers, I think that you can turn off the tubes. Just don't move the cables. I have no tube components now, but I used to have your concern. I did turn off the amp when not playing music. I did leave the preamp on, however. Breakin may take somewhat longer, however.

I now have a Koda K 10 line stage, whose maker say can be turned off at night, but I think it is actually the case that it benefits from being turned off. I also turn off the BMC M2 amps out of concern about electricity consumption.
More to discover